-
Serialport
基本功能都有，可自定义波特率、校验位、数据位、停止位，并且能够收发数据(Basic functions are available. It can customize baud rate, check bits, data bits, stop bits, and can send and receive data.)
- 2020-06-16 04:20:01下载
- 积分：1
-
SerialPortConnection
说明： C# 语言实现指纹一对一的录入以及一对一多对一验证等等(C# Language implements fingerprint one-to-one input and one-to-one, one-to-many, one-to-one verification, etc.)
- 2020-06-20 22:40:01下载
- 积分：1
-
哈哈通用C语言函数
哈哈通用C语言函数-Haha common C language function
- 2022-02-14 13:13:32下载
- 积分：1
-
正弦波的VHDL代码，使用Xilinx logibox产生正弦波输出
sine wave vhdl code that generates sine wave output using logibox in xilinx
- 2022-08-14 12:51:09下载
- 积分：1
-
牛拉法潮流计算程序(附3机9节点结果对比)
基于牛顿拉夫迅算法的IEEE3机9节点系统潮流计算程序(Power flow calculation program for 9 node system of IEEE3 based on Newton rash fast algorithm)
- 2017-12-01 11:05:44下载
- 积分：1
-
PFM - Barcelona
说明： Documentation for vanets simulation// omnet++
- 2021-01-15 17:18:45下载
- 积分：1
-
音视频编码技术-课程作业2
说明： 全搜索算法重构图。像顾名思义，穷尽法就是对搜索范围内的每个位置都进行计算并比较，从原图像块中找到与待匹配块最相似（误差最小）位置的方法。对于一个搜索范围为[-7,7]的区域来说，x，y两个方向全部搜索一遍需要进行 15X15 = 225 次计算。穷尽法的缺点很明显就是计算量太大，速度很慢，另一方面，由于全部范围都进行了计算，其匹配精度是最高的。(Reconstruction graph of full search algorithm. As the name implies, the exhaustive method is to calculate and compare each position within the search range, and find the most similar (least error) position with the block to be matched from the original image block. For an area with a search range of [- 7,7], 15x15 = 225 calculations are required for searching both directions X and Y once. The disadvantage of exhaustive method is that the calculation is too large and the speed is very slow. On the other hand, the matching accuracy is the highest because all the ranges are calculated.)
- 2020-12-29 11:09:01下载
- 积分：1
-
camel camel camel camel
camel camel camel-camel camel camel camel
- 2022-05-19 14:09:23下载
- 积分：1
-
Simultaneous SAR and GMTI using ATIDPCA
In previous work, we presented GMTI detection and geo-location results from the AFRL Gotcha challenge data set, which was collected using a 3-channel, X-band, circular SAR system. These results were compared against GPS truth for a scripted vehicle target. The algorithm used for this analysis is known as ATI/DPCA, which is a hybrid of alongtrack interferometry (ATI) and the displaced phase center antenna (DPCA) technique. In the present paper the use of ATI/DPCA is extended in order to detect and geo-locate all observable moving targets in the Gotcha challenge data,
including both the scripted movers and targets of opportunity. In addition, a computationally efficient SAR imaging technique is presented, appropriate for short integration times, which is used for computing an image of the scene of interest using the same pulses of data used for the GMTI processing. The GMTI detections are then overlaid on the SAR image to produce a simultaneous SAR/GMTI map.
- 2017-11-21 16:48:58下载
- 积分：1
-
只想下载 只想下载 只想下载 只想下载
只想下载 只想下载 只想下载 只想下载-Just want to download just want to download just want to download just want to download just want to download just want to download just want to download
- 2022-01-25 17:19:43下载
- 积分：1
