-
GMM-GMR-v2.0
GMM-GMR的matlab实现，高斯混合模型-高斯混合回归的matlab实现。(Implementation of GMM-GMR by MATLAB)
- 2020-06-21 22:00:02下载
- 积分：1
-
裂缝检测访问了大量的计算机代码，没有测试过
计算机断口检测访问很多代码的,没试用过-Fracture Detection visit a lot of computer code, not tested
- 2023-03-18 20:10:04下载
- 积分：1
-
zuixiaoerchengyichuansuanfa
基本最小二乘和加权最小二乘算法程序（包括一次完成算法和递推算法）(Basic least squares and weighted least squares algorithm (including one-time completion algorithm and recursive algorithm))
- 2017-04-21 15:26:20下载
- 积分：1
-
opencv OpenCV is cross
opencv OpenCV is cross-platform middle-to-high level API that consists of a few hundreds (>300) C functions. It
does not rely on external numerical libraries, though it can make use of some of them (see below) at
runtime, if they are available
- 2023-01-08 07:20:02下载
- 积分：1
-
精英_变异遗传算法
说明： 利用遗传算法对电动汽车有序充电进行优化；优化目标包括充电费用最低，充电时间达到要求（电动汽车充到足够的电）
考虑电动汽车充电对电网负荷的影响，使负荷峰谷差最小(The genetic algorithm is used to optimize the orderly charging of ev.The optimization goals include the lowest charging cost and the required charging time (the electric car is fully charged).
Considering the impact of EV charging on grid load, the peak and valley difference of load is minimized)
- 2021-04-04 16:29:04下载
- 积分：1
-
PLSMATLAB
偏最小二乘回归的MATLAB实现，数据是贝壳的光谱数据，附带了平滑预处理程序(MATLAB implementation of partial least squares regression)
- 2018-03-03 13:32:12下载
- 积分：1
-
ECE451-LCS-Assignment-01-Solutions
Linear Control Systems
- 2018-10-09 17:16:25下载
- 积分：1
-
[程序源代码]雷达中的微多普勒效应
里面记载了雷达微多普勒效应的源代码，其中还包括飞机等目标。(It records the source code of radar micro-Doppler effect)
- 2021-04-04 11:29:04下载
- 积分：1
-
基于CSM自适应波束形成――酉聚焦
％ 8阵列；
％信噪比为10dB 干扰噪声比为20dB 干扰信号与需要信号不相关.
％干扰和信号频率所在范围为8...
基于CSM自适应波束形成――酉聚焦
％ 8阵列；
％信噪比为10dB 干扰噪声比为20dB 干扰信号与需要信号不相关.
％干扰和信号频率所在范围为80―120Hz，相对带宽为40％ ，入射角度分别为seta_S_reg、seta_J_reg -CSM-based adaptive beamforming- Unitary Highlights 8 array 10dB signal to noise ratio for the interference noise ratio of 20dB interference signal and the need to signal irrelevant. Interference and signal frequency range is where the 80-120Hz, the relative bandwidth of 40 , respectively angle seta_S_reg, seta_J_reg
- 2022-11-19 20:15:04下载
- 积分：1
-
本文介绍了在自由口通信模式下，用计算机读写S7
本文介绍了在自由口通信模式下，用计算机读写S7-200 PLC存储区内相邻的多个字
节数据的通信程序设计方法，程序设计中采用了多种可靠性措施。 -In this paper, in a free port communication mode, using the computer to read and write S7-200 PLC storage area adjacent to a number of bytes of data communication program design methods, procedures designed to use a variety of reliability measures.
- 2022-01-22 03:49:14下载
- 积分：1
