登录
首页 » LabView » 超声波加红外测距传感器监控

超声波加红外测距传感器监控

于 2020-07-10 发布 文件大小:43KB
0 110
下载积分: 1 下载次数: 18

代码说明:

  在labview使用超声波传感器和红外传感器进行距离的监控,本程序监控了5个超声波传感器。(In the use of LabVIEW ultrasonic sensors and infrared sensors for distance monitoring, this program monitors 5 ultrasonic sensors.)

文件列表:

超声波加红外测距传感器监控\未命名 17.vi
超声波加红外测距传感器监控

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • LabVIEW与S7-1200系列PLC的通信方法
    LabVIEW与S7-1200系列PLC基于Modbus+TCP_IP协议的通信方法。(Communication method between LabVIEW and S7-1200 series PLC based on Modbus+TCP_IP protocol)
    2018-07-18 15:45:27下载
    积分:1
  • FreeCOM
    labview与串口通信得到串口示波器的波形图(get chart serial port)
    2016-03-21 09:51:48下载
    积分:1
  • 实验8_信道估计与时域均衡
    说明:  通过labview实现通信信道仿真中的信道估计以及时域均衡,注意这个是以及完整实现了信道的搭建,通过添加时域均衡以及信道估计实现最终的仿真(The channel estimation and time-domain equalization in communication channel simulation are realized by labview. Note that this is to build the channel completely. The final simulation is achieved by adding time-domain equalization and channel estimation.)
    2019-06-06 11:21:23下载
    积分:1
  • jianwang3
    剑网3插件写作.基础知识。自学也可以写一手好插件!!!!!!!!!!!(Jian Wang 3 plug-in writing)
    2014-05-21 10:48:33下载
    积分:1
  • 信号发生器vi设计
    LabVIEW编写的一个信号发生器程序,可选择正弦波、方波、三角波等(A signal generator program written by LabVIEW can select sine wave, square wave, triangle wave, etc.)
    2019-04-25 13:27:07下载
    积分:1
  • Labview3Dcontrols_examples
    Labview的3D控件的功能介绍,还有三个例子程序:陀螺仪,2D魔方,3D魔方。(Function Labview 3D controls introduction, there are three examples: gyroscope, 2D Rubik' s Cube, 3D cube.)
    2014-01-26 09:41:19下载
    积分:1
  • YAV USB采集卡 VB例
    说明:  这是一个基于Labview的usb模拟量数据采集卡的例程源码,可用于二次开发(This is a routine source code of USB analog data acquisition card based on Labview, which can be used for secondary development.)
    2020-06-17 11:40:02下载
    积分:1
  • calculator
    简易计算器,实现加、减、乘、处、开方等功能。(Simple calculator to add, subtract, multiply, at the square root function.)
    2012-08-26 21:49:02下载
    积分:1
  • 拍照
    说明:  使用Labview进行实时调用摄像头、按键拍照、根据俯仰角和方向角找到图像中的位置(Use LabVIEW to call the camera in real time, press the key to take photos, and find the position in the image according to the pitch angle and direction angle)
    2019-12-10 14:23:56下载
    积分:1
  • 拉力传感器电机控制
    数据采集卡采集拉力值,与预先设定的拉力值进行比较,然后PID运算,控制相应的PWM占空比输出,最终控制电机的速度(The data acquisition card collects the pull value and compares it with the pre-set pull value. Then the PID arithmetic is used to control the output of the corresponding PWM duty cycle, and finally the speed of the motor is controlled.)
    2020-06-17 02:00:01下载
    积分:1
  • 696518资源总数
  • 104269会员总数
  • 31今日下载