-
创新实验
说明： 基于TCP/IP协议的声音传输，包括上位机和下位机(Voice transmission based on TCP / IP protocol)
- 2021-03-09 12:53:26下载
- 积分：1
-
xinhaocaiji-
用于振动信号的采集，LABVIEW程序，用于齿轮箱等机械设备的振动故障诊断。(For vibration signal acquisition, LABVIEW program for vibration fault diagnosis of gearboxes and other mechanical equipment.)
- 2012-05-14 16:11:44下载
- 积分：1
-
labview-data
通过设置图形的属性节点，活动曲线以及曲线是否可见来实现用复选框控制对应曲线波形的有无，非常实用！(Set graphics attribute nodes activity curve, and the curve is visible to realize the presence or absence of the corresponding curve waveform check box control, very useful!)
- 2020-10-31 16:29:56下载
- 积分：1
-
hanshuxinhaofashengqi
1．采用Labview设计一虚拟函数信号发生器， 通过数据采集卡输出波形信号，调节信号的相关参数，可观察示波器上波形的变化情况。
⑴ 以NI MyDAQ数据采集卡作为输出接口；
⑵ 数据采集卡输出多种信号，至少完成三种波形：正弦波、三角波、方波(可调占空比)的输出，同时前面板上显示各输出波形；
⑶ 频率、幅值、初相位、直流偏移量和方波的占空比（0～100 ）等参数可以通过前面板控件调节。
⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes.
⑴ with NI MyDAQ data acquisition card as output interface
⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel
⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust.
⑷ output waveform can be displayed on the front panel.)
- 2015-04-25 18:26:52下载
- 积分：1
-
jiansuqi
基于Labview虚拟仪器设计界面，检测减速器的转角及其回程误差指标。(Based on Labview virtual instrument interface design, testing reducer corner and return error specification.)
- 2020-12-04 21:39:24下载
- 积分：1
-
NO.4电驱测试
说明： 通过labview模拟实现电驱测试，包含功率曲线等(Realization of electric drive test by LabVIEW simulation)
- 2021-03-25 16:25:54下载
- 积分：1
-
bridge-analysis-code
桥梁模态测量分析程序，用于桥梁一阶、二阶、三阶模态分析(Measurement of the bridge modal analysis program)
- 2020-12-19 21:19:09下载
- 积分：1
-
position control - 09 04 - 副本
电机转速，基于labview。伺服电机控制程序(Motor speed based on LabVIEW. Servo motor control program)
- 2018-05-13 19:10:00下载
- 积分：1
-
UsingTheProgramToGenerateAtriggerEvent
labview中用程序去产生一个触发事件是个难点，相关的介绍和例子并不多，本程序使用值属性信号结点改变的方法去产生一个事件，实现程序控制产生触发事件的功能，labview开发版本8.2。(labview using the program to generate a trigger event is difficult, relevant examples of the introduction are not many,here we use the value change of the node attribute of the signal to generate an event, the realized the program control functions to generate trigger events, the version of labview development is 8.2 .)
- 2009-04-15 02:58:25下载
- 积分：1
-
usb6251
关于如何使用NI公司USB-6251数据采集卡的参考文献(Companies on how to use NI USB-6251 data acquisition card References)
- 2021-03-08 16:59:28下载
- 积分：1
