-
PIC12F675
PIC12F675单片机定时程序及仿真，资料比较全，建议初学者学习(PIC12F675 microcontroller timer program and simulation, data comparison, recommended for beginners to learn)
- 2014-07-17 16:22:03下载
- 积分：1
-
Multiple-18b20-
利用单片机控制多个18b20，并将温度显示在1602 LCD上面(SCM control multiple 18b20, and in 1602 LCD temperature display above)
- 2014-05-27 14:20:30下载
- 积分：1
-
1602-c-program
说明： 1602液晶C程序，放在实验板可以使用，里面有仿真电路图，容易理解(1602 LCD C program can be used on the test board, which has simulated circuit, easy to understand)
- 2011-04-08 09:02:56下载
- 积分：1
-
PIC红外接收程序
红外线遥控接收程序，接收的是一个电视遥控器编码，共25个按锓 20140727经过调试，可以正常收码;收到的码按从高到低，存放在rx3,rx2,rx1,rx0四个寄存器中。(Infrared remote control receiver program, receiving is a TV remote encoding, a total of 25 to 20140727 Qin after debugging, can normally receive code; the code according to the received from high to low, stored in RX3, rx2, rx1, rx0 in the four registers.)
- 2017-11-25 12:36:31下载
- 积分：1
-
51to
dssss ssrrrr rfvsdwewxxs
- 2014-10-08 23:10:37下载
- 积分：1
-
bb
说明： ns中一个模拟仿真的全部工程，包括协议的添加 以及仿真结果的分析方法(ns of a simulation of all the works, including the agreement to add, as well as simulation results of the analysis method)
- 2009-05-04 22:55:43下载
- 积分：1
-
GD32-ADC
说明： 国产ARM芯片，GD32F103系列，替代STM32F103系列，ADC采集项目，编译即可通过，多支持国产芯片。(Domestic ARM chip, gd32f103 series, replace STM32F103 series, ADC acquisition project, compile can pass, most support domestic chips.)
- 2021-03-06 15:29:30下载
- 积分：1
-
visualport
这是一个虚拟串口和红外口的例子的源代码。(This is a virtual serial port and infrared mouth of the source code examples.)
- 2007-03-22 11:11:40下载
- 积分：1
-
LCD
用C语言编写STM32嵌入式程序，设计一个万年历系统，并用HX1230屏显示相关的时间信息。
基本要求：
1.C语言程序要求是模块化设计。
2.该万年历要求能显示时间（时、分、秒）、年月日及闹钟定时时间（分、秒）。
3.该系统由2-3个按键可调整显示的时间、年月日及闹钟定时时间，具体各个按键功能及编程方式自定。
4.该闹钟可以定时时间到，LED将发出提示闪光，且持续30s。
5.HX1230屏能驱动显示。
6.定时时间可被打断，即打断后恢复时继续计时。
7.设置闹钟报警功能；
8.利用STM32自带的温度传感器功能，使系统能显示当前环境温度值。(STM32 embedded program is written in C language, a calendar system is designed, and relevant time information is displayed on HX1230 screen.
Basic requirements:
1. The requirement of C language program is modular design.
The calendar requires that time (hours, minutes, seconds), year, month, day and alarm clock timing time (minutes, seconds) be displayed.
3. The system can adjust the display time, year, month, day and alarm clock timing time by 2-3 keys, and the function and programming mode of each key are self-determined.
4. The alarm clock can be scheduled to arrive, and the LED will give a prompt to flash, and lasts for 30 seconds.
5. HX1230 screen can drive display.
6. Timing time can be interrupted, i.e. when the interruption is resumed, the timing will continue.
7. Setting alarm function of alarm clock;
8. Using the temperature sensor function of STM32, the system can display the current environmental temperature)
- 2020-06-25 05:00:02下载
- 积分：1
-
test_RTC_Alarm
STM32L152的定时唤醒程序,唤醒之后PB10LED闪烁(STM32L152 timer wake-up program, wake up after PB10LED flashing)
- 2017-05-26 15:18:27下载
- 积分：1
