登录
首页 » matlab » pinghuachuli-1

pinghuachuli-1

于 2020-11-23 发布 文件大小:1KB
0 343
下载积分: 1 下载次数: 5

代码说明:

  利用五点滑动平均法对信号进行平滑处理,消除噪声信号的影响(5 moving average method is used to analyse the signal smoothing, eliminate the influence of the noise signal)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • TrajectoryandSpeedControl
    Speed control for a specific trajectory for a robotic manipulator
    2009-05-19 01:11:42下载
    积分:1
  • REGSPEED
    THE REGULATOR OF SPEED OF DOUBLE FEED INDUCTION GENERATOR
    2010-05-15 04:14:35下载
    积分:1
  • MATLAB-algorithm-
    matlab 常用算法大全,很全,很好,大家可以借鉴学习的。(matlab commonly used algorithm Daquan, very full, very good)
    2014-09-24 14:22:54下载
    积分:1
  • lagrange
    Lagrange Interpolation
    2012-02-15 16:52:34下载
    积分:1
  • wavenengliang
    小波分析语音信号并计算各IMF包络的能量熵(Wavelet analysis of vibration signals and calculate the energy entropy IMF envelope)
    2014-07-18 12:51:07下载
    积分:1
  • fdtd-1d
    电磁场一维的fdtd,适用于初学者参考,内为txt格式,直接复制粘贴到matlab即可。(Electromagnetic field one-dimensional fdtd)
    2013-04-07 11:51:35下载
    积分:1
  • ELM_MultiOutputRegression
    ELM算法是一种新型的学习算法,速度较快,误差小,目前研究较多的一种算法,提供的是多输出回归问题的ELM算法的matlab实现。(ELM algorithm matlab realize)
    2014-03-05 21:14:15下载
    积分:1
  • 1
    主成分分析的matlab源程序,用以标准化数据,精简指标,减少指标之间信息的重叠。(Principal component analysis matlab source for standardized data, streamline indicators, reduce duplication of information between indicators)
    2014-02-23 13:27:22下载
    积分:1
  • concavefalt2
    平凹腔激光模式计算程序,利用边界元方法计算,matlab编程!(concave cavity laser mode procedures, the use of the boundary element method, the Matlab programming!)
    2006-07-03 19:38:33下载
    积分:1
  • trns
    The model used for creating the reference voltage is shown in Fig. 4. First, photovoltaic output current (Ipv) and output voltage (Vpv) are passed through a first order low pass filter with a magnitude of G = 1 and a time constant of T = 0.01 seconds in order to filter out the high frequency components or harmonics from these signals as shown in Fig. 5 and Fig. 6. The filtered current and voltage signals (Ipv_F and Vpv_F) are then fed into the MPPT control block that uses the Incremental Conductance Tracking Algorithm. An algorithm that is based on the fact the slope of the PV array power curve shown in Fig. 7 is zero at the Maximum Power Point (MPP), positive on the left of the MPP, and negative on the right. The MPP can thus be tracked by comparing the instantaneous conductance (I/V) to the incremental conductance (∆ I/∆ V) [11] as in (1):
    2013-07-23 17:45:44下载
    积分:1
  • 696518资源总数
  • 106227会员总数
  • 11今日下载