网站首页

登录

system_identification

于 2016-03-21 发布文件大小:26KB

 0  212

下载积分: 1 下载次数: 26

我要下载

代码说明：

根据系统的输入和输出，辨识系统的的传递函数。该系统为6阶系统，通过降阶降为2阶后，加入状态反馈和状态观测器，调整参数使2阶系统稳定，最后用于控制原6阶系统。阶跃响应和bode图效果都不错。(Based on the input and output of the system, the transfer function of the system is identified. The system is a 6 order system. After the order is reduced to 2 order, the system is added with the state feedback and the state observer, which adjusts the parameters to make the 2 order system stable. Finally, it is used to control the original 6 order system. Step response and Bode figure results are good.)

文件列表：

系统辨识及状态反馈
..................\LSI_CW3.mat,23651,2016-01-07
..................\mian.m,6337,2016-03-09

下载说明：请别用迅雷下载，失败请重下，重下不扣分！

发表评论

0 个回复

simulinksumilator
Simulink 动态系统建模与仿真，pdg格式，需用超星阅览器打开(Simulink Dynamic System Modeling and Simulation, pdg format, need to open browser Chaoxing)

2007-10-17 09:18:11下载

积分：1
ML
说明：此算法为基于最大似然方法的DOA估计是区别于子空间类的DOA算法但需要多维搜索计算量较大(This algorithm is based on the maximum likelihood method of DOA estimation is different from the sub-space kind of DOA algorithm but calculating the volume of the larger multi-dimensional search)

2007-11-16 07:45:22下载

积分：1
zhaoxiaopu
位置指令为幅值为1.0的阶跃信号，r（k）=1.0。网络结构为1-4-1，高斯函数的参数值取Cj=[-2 -1 1 2]T ，B=[0.5 0.5 0.5 0.5]T 。网络权值学习参数为η=0.30，α=0.05 。PID控制各参数的初RBF网络控制，被控对象为G（s）= 取采样时间为1ms，采用Z变换进行离散化，离散化后的被控对象为 y(k)=-den(2)*y（k-1）-den(3)*y(k-2)+num(2)*u(k-1)+num(3)*u(k-2) 始值为，kp=20， kd=0.3， ki=0.1。 (Position command for the step signal amplitude of 1.0, r (k) = 1.0. The network structure is 1-4-1, the Gaussian function parameters taken Cj = [-2-1 1 2] T, B = [0.5 0.5 0.5 0.5] T. Weight learning parameter η = 0.30, α = 0.05. PID control parameters at the beginning of each RBF network control, the controlled object is G (s) = take the sampling time is 1ms, using the Z transform discrete, discretized controlled object is y (k) =-den (2)* y (k-1)-den (3)* y (k-2)+num (2)* u (k-1)+num (3)* u (k-2) initial value, kp = 20, kd = 0.3, ki = 0.1.)

2013-07-22 21:20:28下载

积分：1
matlab
说明： Household变换，利用仿真数据进行ftt，最小二乘法的多项式拟合(House transform, polynomial fitting of FTT and least square method with simulation data)

2020-05-23 20:34:45下载

积分：1
perceptronexample
感知器分类的一个例子，分成两类的分类器,用MATLAB实现(perceptron example for matlab)

2009-12-18 10:09:48下载

积分：1
hht_toolbox_20040808
EMD 和 Hilbert-Huang 变换 matlab工具箱(EMD and HilbertHuang transform matlab toolbox)

2009-06-11 17:30:55下载

积分：1
hilbert
将实信号变换为复信号，提取信号幅值、相位角，计算相位同步指数，分析各组信号数据之间的同步稳定性。(The signal is converted into a complex signal, extraction of signal amplitude, phase angle, calculation of phase synchronization index, analysis of stability of synchronization between each signal data.)

2013-12-19 11:41:14下载

积分：1
ofdm_2
OFDM仿真包括信号源,卷积码编码，交织，qpsk调制，IFFT，组帧，上采样，通过FIR滤波器通过高斯信道，再经过低通FIR滤波器，下采样，拆帧，FFT，qpsk解调，接收数据；计算误比特率(OFDM simulation including the signal source, sampling convolutional encoding, interleaving, QPSK modulation, IFFT, frame,, through the FIR filter through Gauss channel, and then through the low pass FIR filter, sampling, demolition of frame, FFT, QPSK demodulation, the received data bit error rate calculation)

2020-12-03 14:49:25下载

积分：1
p05
Sourcecode of matlab for recognition that the bottel is full?

2010-10-29 05:57:50下载

积分：1
three_phase_motor_speed
三相异步电机反转，matlab仿真，希望大家支持(Three-phase asynchronous motor reversal, matlab simulation, hope you will support the)

2009-05-20 11:44:41下载

积分：1

696518资源总数
106235会员总数
12今日下载