登录
首页 » matlab » jei-nk16

jei-nk16

于 2017-04-01 发布 文件大小:6KB
0 86
下载积分: 1 下载次数: 1

代码说明:

  正确率可以达到98%,仿真图是速度、距离、幅度三维图像,这是第二能量熵的matlab代码。( Accuracy can reach 98 , FIG simulation speed, distance, amplitude three-dimensional image, This is the second energy entropy matlab code.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • DSBF
    delay and sum beamforming algorithm
    2007-04-09 05:57:25下载
    积分:1
  • rwtransform
    计算wigner-randon变换的频域解线调代码(Transform the calculation of Wigner-Randon the frequency domain dechirp code)
    2013-05-19 17:36:08下载
    积分:1
  • Tr_1
    Study modes phase transformer experience load and short-circuit calculation of parameters of the equivalent circuit of the transformer.
    2014-01-23 07:53:53下载
    积分:1
  • ACOmatlab
    蚁群算法的Matlab程序,用于连续函数优化(Ant colony algorithm Matlab program for continuous function optimization)
    2010-06-24 14:05:57下载
    积分:1
  • ccsp
    matlab power spectrue(matlab)
    2009-12-21 17:03:12下载
    积分:1
  • Range-and-azimuth-compression
    雷达成像技术包含(一)线性调频信号的匹配及源代码;(二)雷达采集信号的距离向压缩及源代码(三)雷达采集信号的距离徙动校正与方位向压缩及源代码(The radar imaging technique include (a) linear FM signal matching and source code (b) the distance of the radar signal acquisition to the radar signal acquisition, compression and source code (c) distance migration correction and azimuth compression and source code)
    2012-04-26 21:08:44下载
    积分:1
  • identifyspacialchen
    采用陈前荣的空域法鉴别运动模糊方向 需要图像满足功率谱各向同性 否则误差大(motion blur theta identify chenqianrong’s method)
    2012-05-17 21:12:24下载
    积分:1
  • Subdomain
    加权余量法--子域法求解一维扩散方程。参考书《Computational Techniques for Fluid Dynamics》(The weighted residual Law- sub-domain method for solving one-dimensional diffusion equation. Reference book " Computational Techniques for Fluid Dynamics" )
    2013-05-21 22:15:01下载
    积分:1
  • GMD_update
    一种基于几何均值分解的混合预编码技术研究(Hybrid precoding based on geometric mean decomposition)
    2020-12-25 20:39:04下载
    积分:1
  • C2
    说明:  s1 is the M-file description of the SIMULINK system named s1. The block-diagram can be displayed by typing: s1. SYS=s1(T,X,U,FLAG) returns depending on FLAG certain system values given time point, T, current state vector, X, and input vector, U. FLAG is used to indicate the type of output to be returned in SYS.
    2010-03-03 17:12:18下载
    积分:1
  • 696518资源总数
  • 104349会员总数
  • 32今日下载