-
fashengqi
基于labview的虚拟波形发生器，能够实现正弦、余弦、锯齿波的产生(Labview-based virtual waveform generator, to achieve the sine, cosine, sawtooth generation)
- 2013-12-22 16:15:06下载
- 积分：1
-
基于LabVIEW的通用自动测试系统设计
基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)
- 2020-10-24 12:27:23下载
- 积分：1
-
sfafdsa
在labview开发环境下面，利用百度API调用百度地图，把车辆信息显示在地图上面。(In the following labview development environment, API calls use Baidu Baidu map, the vehicle information is displayed in the map above.)
- 2015-10-13 20:31:33下载
- 积分：1
-
Auto-PWM
labview程序，电机PWM控制，labview作为上位机(labview program, the motor PWM control, labview as a PC)
- 2012-06-19 09:40:37下载
- 积分：1
-
12
说明： 利用LabVIEW实现_PC与PCI-1710HG数据采集卡组成的虚拟仪器(LabVIEW virtual instrument _PC data acquisition card PCI-1710HG)
- 2012-11-22 21:36:03下载
- 积分：1
-
数据采集编程指南 上篇
Introduction of NI data acquisition hardware
1. Basic components of a complete data acquisition system
2. NI provides data acquisition hardware products based on which platforms and which application areas they are suitable for respectively.
3. What important parameters should be paid attention to in the process of hardware selection of data acquisition equipment
- 2020-06-21 20:00:02下载
- 积分：1
-
16 阈值分割
阈值分割的各种方法的集合。局部阈值分割法，全局手动、自动阈值分割(A set of thresholding methods. Local Threshold Segmentation, Global Manual and Automatic Threshold Segmentation)
- 2020-06-16 15:00:02下载
- 积分：1
-
CCD Driver
说明： CCD相机控制程序，用labview 驱动线阵CCD，可以设置采样时间/频率/曝光度等参数。(CCD driver,drive CCD camra with labview, with controlling of sample time parameter.)
- 2019-04-06 02:59:11下载
- 积分：1
-
CRC16a
串口自动换算CRC代码，编写时直接可以调用(Serial port automatically converts CRC code, which can be called directly when writing.)
- 2020-06-21 20:20:01下载
- 积分：1
-
LABVIEW-Custom-Grid
LABVIEW 表格中可输入颜色框_下拉框_选择框(Labview custom grid vi)
- 2021-01-21 15:38:46下载
- 积分：1
