登录
首页 » matlab » S_665_buck_boost_14a

S_665_buck_boost_14a

于 2019-02-18 发布 文件大小:17KB
0 112
下载积分: 1 下载次数: 2

代码说明:

  该仿真模型搭建了Buck-boost仿真模型,实现输入电压的变换(The Buck-boost simulation model is built to realize the input voltage conversion.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论


0 个回复

  • allthebest
    Additionally, LTE supports operation both in paired and unpaired spectrum (FDD and TDD) using channel bandwidths of approximately 1.4MHz up to 20MHz. The frequency domain scheduling can be done in OFDMA. One of the main challenges in OFDMA is the high peak-to-average radio of the transmitted signal, which requires linearity in the transmitter. The linear amplifiers have low efficiency therefore, OFDMA is not an optimized solution for a mobile uplink where the
    2013-01-01 13:39:42下载
    积分:1
  • xnbm
    Matlab关于香农信道容量公式演示实验Matlab关于香农信道容量公式演示实验(Matlab on Shannon channel capacity formula Matlab demonstration experiment on the Shannon channel capacity formula Demonstration)
    2010-05-12 21:33:36下载
    积分:1
  • xsk_RMA
    合成孔径雷达RMA算法的matlab程序(RMA algorithm for synthetic aperture radar)
    2011-08-26 15:35:29下载
    积分:1
  • wuyuan
    三种无源滤波器输出波形比较分析,包括L型滤波器,LC型滤波器,LCL型滤波器(three kinds of filter)
    2015-06-08 11:08:44下载
    积分:1
  • MATLAB CCA
    MATLAB的cca算法实现,输入数据集,输出系数矩阵(Realization of CCA algorithm in MATLAB)
    2020-06-30 03:20:01下载
    积分:1
  • m_series
    用移位寄存器产生M序列的MATLAB软件实现(M generated using shift register sequences MATLAB software)
    2008-03-14 19:00:45下载
    积分:1
  • eziir16
    是学习matlab的很好程序资料 可以用来方便设计iir滤波器(Matlab is a good learning process can be used to facilitate the design of filter iir)
    2007-03-19 15:00:53下载
    积分:1
  • ssmcmcmatlab
    semi-supervised MCMC classification
    2007-09-27 21:56:31下载
    积分:1
  • 2
    说明:  基于小波变换的多尺度图像边缘检测matlab源代码(在Matlab7.0下运行) (Based on wavelet transform multi-scale edge detection matlab source code (at run Matlab7.0))
    2009-04-02 23:27:57下载
    积分:1
  • LETITSNOW-
    使得最近打开的MATLAB图形开始下雪,如果没有已经打开的窗口,则首先创建一个窗口。(LETITSNOW- Make the figure snow! Usage: ------ letitsnow - Create snow in the CURRENT figure. If no figure exists, an empty figure will be created. letitsnow(figure_hdl) - Create snow in the figure represented by figure_hdl letitsnow(figure_hdl, color)- Create snow with the specified color color is a scalar ranged 0~1)
    2012-03-22 22:44:55下载
    积分:1
  • 696518资源总数
  • 104737会员总数
  • 20今日下载