登录
首页 » matlab » FFT

FFT

于 2021-04-10 发布 文件大小:21KB
0 163
下载积分: 1 下载次数: 31

代码说明:

  matlab汽车平顺性加权加速度评判标准(Matlab vehicle ride comfort evaluation)

文件列表:

FFT\2013-01-12-14-38-00.can, 35744 , 2013-01-12
FFT\wangfft.m, 1722 , 2014-01-07
FFT\使用说明.doc, 9216 , 2014-01-09
FFT, 0 , 2018-04-29

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Basic
    在matlab环境里,利用music算法对波达方向角度进行估计运算(use music for doa)
    2015-01-08 16:00:13下载
    积分:1
  • Rt_MBOC
    RX_MBOC的自相关函数,MBOC(6,1,1/11)的自相关函数(RX of MBOC,MBOC(6,1,1/11))
    2016-06-02 09:26:37下载
    积分:1
  • 贪心算法实
    说明:  一个用matlab编写的贪婪算法程序,可以嵌入到其他程序中(Matlab prepared a greedy algorithm procedures, can be embedded in other procedures)
    2021-01-29 16:28:34下载
    积分:1
  • ceshi_Excel
    使用matlab实现对excel文档的写操作,以写学生成绩报告为例(Use matlab to achieve excel document write operation to write the report as an example of student achievement)
    2013-12-03 22:28:30下载
    积分:1
  • activeContoursSnakesDemo
    本演示实现了主动轮廓模型由Kass等人提出。 要运行它的图形用户界面 1。基于MATLAB型引导提示。 2。关于“到现有的图形用户界面,点击” 3。选择在与本文件相同的目录snk.fig文件 4。按一下上方的绿色箭头启动图形界面 一旦GUI已经启动,您可以通过使用蛇 1。点击“新形象”,并加载输入图像。提供的样品图像。 2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。 3。只要你点击“过滤器”,头发会出现交叉,用他们和你左击鼠标,您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下,你应该单击对象周围的一切你想要的部分。最后一点,必须挑选使用右键单击,以阻止更多的积分为MATLAB的要求。 4。设置各种蛇参数(在能源方面的相对权重的蛇目标函数)或离开它们的默认值,然后按一下他们“迭代”按钮。蛇会出现和移动,因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al. To run it with GUI 1. Type guide on the matlab prompt. 2. Click on "Go to Existing GUI" 3. Select the snk.fig file in the same directory as this file 4. Click the green arrow at the top to launch the GUI Once the GUI has been launched, you can use snakes by 1. Click on "New Image" and load an input image. Samples image are provided. 2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image. 3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points. 4. Set the various snake paramete)
    2010-07-05 11:54:13下载
    积分:1
  • MATLAB
    MATLAB写自相关函数,M序列的MATLAB产生(MATLAB to write auto-correlation function, M sequences generated MATLAB)
    2008-03-21 13:36:23下载
    积分:1
  • mapprojection
    matlab用于图形图像处理,小波分析等(a book oabout matlab,which can use operating picture,wavelet,etc)
    2009-12-23 09:12:05下载
    积分:1
  • Fuzzy---simulink
    里面有三个二维模糊调节器分别实现PID控制器的参数Kp,ki,Kd,的调节。其控制原理:根据前面的偏差e和偏差变化ec将三个模糊控制器FC1,FC2,FC3分别进行模糊化,模糊逻辑推理,解模糊化。最后得到pid控制器参数调节量。(There are three-dimensional fuzzy regulator PID controller parameters Kp, ki Kd, adjust. The control principle: the front of the deviation e and error change ec three fuzzy controllers FC1 has FC2, FC3, fuzzification, fuzzy logic inference, defuzzification. Finally, get the pid controller parameter adjustment.)
    2012-04-11 08:43:57下载
    积分:1
  • LaplaceFusion
    拉普拉斯图像融合matlab代码,希望对大家有用。(The matlab code of laplace fusion.)
    2012-05-14 21:30:12下载
    积分:1
  • GettingStartedwithMATLAB
    MATLAB入门,通俗易懂,老外写的,有大量实例。(Getting Started with MATLAB)
    2011-09-21 13:02:40下载
    积分:1
  • 696518资源总数
  • 106215会员总数
  • 5今日下载