网站首页

登录

Grid-Connected-PV-Array

于 2021-04-11 发布文件大小:576KB

 0  174

下载积分: 1 下载次数: 61

我要下载

代码说明：

Two demos illustrate use of SimPowerSystems for modeling a PV array connected to a utility grid. PVarray_Grid_IncCondReg_det.mdl is a detailed model of a 100-kW array connected to a 25-kV grid via a DC-DC boost converter and a three-phase three-level Voltage Source Converter (VSC). Maximum Power Point Tracking (MPPT) is implemented in the boost converter by means of a Simulink model using the “Incremental Conductance + Integral Regulator” technique. PVarray_Grid_PandO_avg.mdl is an average model of a 200-kW array connected to a 25-kV grid via two DC-DC boost converters and a single three-phase VSC. The MPPT controller based on the “Perturb and Observe” technique is implemented by means of a MATLAB Function block that generates embeddable C code.

文件列表：

Project 2

.........\PV Array Demos Help.pdf,267017,2016-01-08

.........\PVarray_Grid_IncCondReg_det.mdl,258296,2012-09-25

.........\PVarray_Grid_PandO_avg.mdl,338971,2012-09-25
.........\PV_model_Param.mdl,32463,2012-09-25

下载说明：请别用迅雷下载，失败请重下，重下不扣分！

发表评论

0 个回复

Chuong-3
Đ ay là chư ơ ng trình mô phỏ ng quá trình biế n đ ổ i tư ơ ng tự sang số ADC

2013-10-29 11:52:58下载

积分：1
LFM
线性调频信号的累加器实现，用于产生线性调频信号，线性调频信号可以用于超声信号的发射，音箱的检测等。(Linear frequency modulated signal to achieve the accumulator, for the production of linear FM signals, linear frequency modulated signal can be used to launch ultrasonic signals, such as speaker detection.)

2009-05-14 01:18:29下载

积分：1
BPnetwork
自适应学习率调整算法来训练BP网络,有利于缩短学习时间(BP network)

2010-02-28 22:21:16下载

积分：1
ctrllab3.0
薛定宇教授 ctrllab工具箱3.0；PID参数仿真用。使用方法：1）解压，并在matlab下导入路径；2）在命令窗口执行ctrllab即可。 (Professor Xue Dingyu ctrllab Toolbox 3.0 PID parameters in simulation. Usage: 1) extract and import under the matlab path 2) In the command window to execute ctrllab.)

2011-04-21 11:42:42下载

积分：1
math_of_convolution
This program shows how convolution works, going through all the steps of exactly what gets added up and multiplied with what. It also explains from the ground-up how to do for-loops in Matlab. (By the way, if you want to see an example of how to "vectorise" code to avoid for-loops altogether, look at the bkprop.m program in my

2012-08-07 12:42:23下载

积分：1
liangziyoudubiliqiankui
两自由度比例前馈simulink模型，测四轮转向的质心侧偏角和横摆角速度(Two degrees of freedom ratio feedforward simulink model, measuring four-wheel steering center of mass of side-slip Angle and yawing angular velocity )

2013-09-19 11:35:16下载

积分：1
xtbszsykz
《系统辨识与自适应控制MATLAB仿真》的程序代码，有很高的参考价值。(MATLAB simulink)

2009-10-11 17:36:03下载

积分：1
lin
电力系统无功对网损的灵敏度，包含雅可比矩阵，各种函数公式(the power system)

2012-11-15 16:54:47下载

积分：1
EXPONENTIAL
making exponential signal with matlab In communications, the purpose of using exponential signals instead of sinosuid ones is to use both halves of signal spectrum(Negative and Positive sides of spectrum). For example an FSK signal can not simply downconverted to DC. because its spectrum is not symmetric around its center frequency, so you should downconvert it with exponential signal( the idea of using I and Q downconverter).

2013-05-25 01:05:06下载

积分：1
SMO_sevo
这是一个基于关于伺服系统的滑模控制的仿真程序，伺服系统为基于S的数学模型，对于研究滑模控制会有帮助(sliding mode control of the sevo system)

2010-06-23 22:03:27下载

积分：1

696518资源总数
106253会员总数
14今日下载