登录
首页 » C51 » Quectel_MC20_Hardware

Quectel_MC20_Hardware

于 2017-01-20 发布 文件大小:2152KB
0 99
下载积分: 1 下载次数: 88

代码说明:

  三合一模块,Mc20的硬件设计手册,已经通过做项目(Triad module, Mc20 hardware design manual, already by doing projects )

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 矩阵
    说明:  蓝桥杯CT107D矩阵键盘的源代码测试使用供学习和参考(Blue Bridge Cup Matrix Keyboard)
    2019-03-24 17:07:57下载
    积分:1
  • STM32-24c64
    STC32的IIC存储芯片24C64操作 通过高度 程序稳定 (STC32 the IIC memory chip 24C64 operating procedures through a highly stable)
    2020-09-30 09:47:43下载
    积分:1
  • fuzhao
    高强度聚焦超声辐照剂量与生物学效应研究.(Study the biological effects of ultrasound irradiation dose and high-intensity focused.)
    2014-01-22 15:25:05下载
    积分:1
  • GestioneLibreria
    gestione biblioteca scolastica
    2013-11-20 19:37:55下载
    积分:1
  • C8051_TCP
    基于CP2200的TCP/IP驱动程序,是嵌入式网络连接的最简单方案(The CP2200-based TCP/IP drivers, embedded network connectivity is the most simple program)
    2008-02-25 14:59:35下载
    积分:1
  • sourcecodeformeter
    采用四端法测试欧姆电阻,并把结果显示在lcd上,采用c8051(Four-terminal method using ohm resistors, and the results displayed in the lcd, using C8051)
    2007-09-11 12:40:36下载
    积分:1
  • smart-car
    在淘宝上购买的毕业论文,价值400的源程序,包含全部文件。一款基于单片机的灭火机器人模型的设计。系统以STC89C52RC单片机为控制核心,创新自制了火焰传感器用来测量火源,使用TCRT5000型光电对管检测循迹黑线,L298驱动电机前后转动,LCD1602液晶显示灭火的次数,通过控制继电器开关风扇灭火。(On Taobao buy thesis, the value of the 400 source code, including all documents. Fire fighting robot model based on a single-chip design. System microcontroller STC89C52RC to control core, innovation homemade flame sensor is used to measure the fire source, tracking black line on the tube use TCRT5000 photoelectric detection, L298 drive motor rotating back and forth, the LCD1602 LCD number of fire-fighting, fire control relay switch fan .)
    2013-05-16 18:52:49下载
    积分:1
  • ProjectOne_V0
    关于用瑞萨单片机使用无线模块的CC1101的源代码。大家交流一下(On the use of Renesas MCU CC1101 wireless module' s source code. We exchange)
    2013-08-20 16:25:50下载
    积分:1
  • data-acquisiton
    数据采集程序,采集波形图数据,并实现数据的存取(data acquisition)
    2020-11-12 21:39:44下载
    积分:1
  • lesson9_1
    在51开发板上,向AT24C02 EEPROM中写入0x(xx),同时读出之后赋值给P1口。注意三处加*********(In the 51 development board, write 0x (xx)to AT24C02 EEPROM , while after reading assigned to P1 port. Note that three plus。)
    2013-07-19 17:20:46下载
    积分:1
  • 696518资源总数
  • 104349会员总数
  • 32今日下载