登录
首页 » Unix_Linux » checkcond

checkcond

于 2015-11-25 发布 文件大小:2KB
0 105
下载积分: 1 下载次数: 1

代码说明:

  If there are no Klingons in this quadrant, we nullify any distress calls which might exist.

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • OLED_TEST
    OLED使用驱动,基于MSP430 单片机(OLED driver for MSP430 Family )
    2014-09-11 12:58:38下载
    积分:1
  • lesson1
    说明:  基于51单片机通信的其中一种,I2C总线通信。(I2C bus communication is one of 51 MCU communication.)
    2020-06-18 18:00:01下载
    积分:1
  • file3_ok
    stm32f107vc 读写ch375扇区,在电路板上测试通过(stm32f107vc read and write ch375)
    2012-09-08 20:22:09下载
    积分:1
  • LED
    一个LED灯带的程序,通过红外遥控器进行遥控,实现变色,七彩跳变等功能(LED lights with a procedure carried out by remote control infrared remote control to achieve color, colorful hopping function)
    2021-03-11 15:19:26下载
    积分:1
  • 信号与系统实验程序文件
    信号与系统;仿真;MATLAB;例子;实验;(Signal and system; simulation; MATLAB; example)
    2021-01-14 15:58:46下载
    积分:1
  • clock
    说明:  古老电子荧光管做的数字钟,可以调时间。整点闹钟。(Electronic fluorescent tubes to do the old digital clock, you can transfer time. The whole point of alarm.)
    2010-03-26 10:00:44下载
    积分:1
  • smg
    用瑞萨16位单片机驱动数码管,循环显示数字(Renesas 16-bit microcontroller with digital tube driver, circulation figures)
    2013-09-03 16:37:51下载
    积分:1
  • STM32-USART-send-and-receive-data-
    本程序目的是提供使用stm32串口收发一帧数据的一种方法,采用中断方式接受和发送,每进一次中断接收或发送一字节,可以实现pc机与板子通信或板子与板子间通信。注意本程序中外接高速晶振为12M赫兹,而大部分板子为8M赫兹,本程序所用芯片是stm32RBT6(The purpose of this procedure is to provide a method of using STM32 serial port to send and receive a data, using interrupt mode to receive and send, every one into the time interrupt receiving or sending a byte, can realize PC and the communication or board and board communication. Note that this procedure the external high-speed crystal oscillator for the 12M Hz, while the majority of board is 8M Hz, the chip used in this procedure is stm32RBT6)
    2020-07-31 10:18:38下载
    积分:1
  • cankao
    高效DPD算法在无线基站设备中,末级功率放大器的失真是影响无线带宽的主要因素之一。当前业界的主流解决方案是采用数字预失真技术,在下行信号中加入失真补偿分量以对消PA输出的失真成分,达到提升带宽的目的。(The distortion of the amplifier is one of the main factors that affect the wireless bandwidth. The mainstream solution of the industry is to use digital pre distortion technology, in the downlink signal to join the distortion compensation component to eliminate the distortion of the PA output components, to achieve the purpose of improving the bandwidth.)
    2015-07-04 17:09:29下载
    积分:1
  • MSC121X_Examples
    MSC121X例程rtc wd spi eeprom (MSC121X_examples code)
    2013-05-20 18:56:25下载
    积分:1
  • 696518资源总数
  • 104269会员总数
  • 31今日下载