-
SVMS-1.0.2
labview的一些功能界面,包括支持向量机(Blind source separation)
- 2014-06-05 08:15:34下载
- 积分：1
-
numberofrandomgraphs
随机数曲线例程，利用libview进行随机数曲线仿真计算(number of random graphs)
- 2013-09-02 15:54:20下载
- 积分：1
-
labview-signal
产生0到100kd的方波。正玄波，三角波，锯齿波和输出为0到10V的电压的信号发生器(0 to 100kd produce a square wave. Sine wave, triangle wave, sawtooth wave and the output voltage from 0 to 10V signal generator)
- 2013-07-09 19:39:27下载
- 积分：1
-
3-1正余弦波形
在波形Graph显件上用两种不同颜色显示一条正弦曲线和一条余弦曲线，每
条曲线长度为128个点，其中正弦曲线的x0 =0，△x=1；余弦曲线的x0 =2，
△x=5。并利用属性节点通过前面板控件改变每条曲线的颜色。
①一个周期128点。
②改变颜色一定要先选择曲线，然后再改变颜色。(A sine curve and a cosine curve are displayed in two different colors on the waveform Graph display.
The length of the bar curve is 128 points, where the sine curve x0 =0, Delta x=1, the cosine curve x0 =2,
Delta x=5. And use the attribute node to change the color of each curve through the front panel control.
One cycle is 128 points.
Change the color must first choose the curve, then change the color.)
- 2018-11-19 12:08:29下载
- 积分：1
-
hanshuxinhaofashengqi
1．采用Labview设计一虚拟函数信号发生器， 通过数据采集卡输出波形信号，调节信号的相关参数，可观察示波器上波形的变化情况。
⑴ 以NI MyDAQ数据采集卡作为输出接口；
⑵ 数据采集卡输出多种信号，至少完成三种波形：正弦波、三角波、方波(可调占空比)的输出，同时前面板上显示各输出波形；
⑶ 频率、幅值、初相位、直流偏移量和方波的占空比（0～100 ）等参数可以通过前面板控件调节。
⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes.
⑴ with NI MyDAQ data acquisition card as output interface
⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel
⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust.
⑷ output waveform can be displayed on the front panel.)
- 2015-04-25 18:26:52下载
- 积分：1
-
Labview--data-playback-and-print
一个laview小程序，实现数据的回放与打印功能(Laview a small program, data playback and print functions)
- 2016-09-22 16:08:30下载
- 积分：1
-
qiaodu
振动信号的峭度指标在labview中实现，对振动信号的评价很准。(Labview achieve signal kurtosis)
- 2021-04-01 12:39:08下载
- 积分：1
-
labviewTCP IP协议
labview tcp协议通讯简单的额小李子(LabVIEW TCP protocol communication)
- 2018-12-05 16:27:39下载
- 积分：1
-
test2
新建子VI（test2
oise_testing.vi），运用Express VI，实现噪声信号的采集、处理、显示和存储(The new sub VI (test2
oise_testing.vi) uses Express VI to realize the acquisition, processing, display and storage of noise signals)
- 2017-06-30 15:38:34下载
- 积分：1
-
智能四路交通灯控制系统模拟
说明： 【智能四路交通灯控制系统模拟】
这款交通灯模拟系统基于labview软件开发，界面全部自己设计，简洁明了，功能多样化、实用化、具体化，最大程度还原真实的十字路口交通灯控制系统。在以往单纯的红绿交替变化上添加功能如下
1.数码管倒计时功能和灯光闪烁功能，四路人行道灯。
2.配备有操作板可以人为设置各路口交通灯的亮灭时间、闪烁频率，报警器频率，字符串提示。控制暂停和全灭。
3.数码管显示的系统实时年月日及时间。
4.显示以及交通管制中的7种模式（普通模式、三向禁行、南北通行、东西通行、夜间模式、维修模式、紧急模式）和每种模式持续的时间（用计时器来体现）。
现实中可以根据实际路况和需要进行有目地的调整，使交通更加通畅高效。([simulation of intelligent four-way traffic light control system]
1. Digital tube countdown function and light flashing function, four-way sidewalk light. 2. Equipped with operation panel, it can manually set the on / off time, flashing frequency, alarm frequency and string prompt of traffic lights at each intersection. Control suspension and total extinction.
3. The real-time date and time of the digital tube display system.
4. Display and seven modes in traffic control (general mode, three-way traffic prohibition, north-south traffic, east-west traffic, night mode, maintenance mode, emergency mode) and duration of each mode (reflected by timer).
In reality, it can be adjusted according to the actual road conditions and needs to make the traffic more smooth and efficient.)
- 2020-06-22 15:30:25下载
- 积分：1
