登录
首页 » matlab » code

code

于 2014-02-24 发布 文件大小:5176KB
0 110
下载积分: 1 下载次数: 13

代码说明:

  去雾算法,包括了matlab代码,和几个可以使用的exe文件(Defogging algorithm)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • QPSKtongbu
    说明:  毕业论文--QPSK中频数字接收的同步算法研究(Thesis- QPSK IF digital receivers synchronization algorithm)
    2010-04-29 14:41:12下载
    积分:1
  • xitongjiaozheng
    设计一超前校正环节,使得超调量为20 ,调节时间为1s。系统单位斜坡稳态响应误差为10 。并作出校正前后后的系统单位阶跃响应时域曲线加以比较。(Design a lead correction link, so the overshoot is 20 , adjust the time of 1s. Steady-state response of the system unit error of the slope is 10 . Made before and after correction and after the system unit step response curves are compared in time domain.)
    2011-05-29 20:07:48下载
    积分:1
  • select
    将彩色图像有选择灰度化的matlab程序(Select graying)
    2013-03-19 18:43:23下载
    积分:1
  • BCH_HDL_ENCODER
    Syntetizable source code of VHDL BCH(1023,1013) encoder. This scheme used by DTMB standart and produce ten redundancy bit on 125 cycles because bus width of 8 bits.
    2010-05-12 21:28:23下载
    积分:1
  • demobpm
    动量bp算法源程序。网上找来的。希望有用。多谢支持(momentum bp algorithm source. The design of the Internet. Hope useful. Thank you for your support)
    2007-02-11 13:08:30下载
    积分:1
  • Demos
    This demo file shows capabilities for PID Controller design and tuning in MATLAB and Simullink
    2013-04-13 02:54:59下载
    积分:1
  • Detect
    基于matlab的动态物体捕捉程序代码,备注详细,方便初学者学习(Capture-based dynamic object matlab program code, detailed notes, easy for beginners to learn)
    2015-02-23 17:34:49下载
    积分:1
  • Highboostfilter
    high boost filter for frequency domain
    2009-12-10 15:10:32下载
    积分:1
  • three_dim_plot
    The model used for creating the reference voltage is shown in Fig. 4. First, photovoltaic output current (Ipv) and output voltage (Vpv) are passed through a first order low pass filter with a magnitude of G = 1 and a time constant of T = 0.01 seconds in order to filter out the high frequency components or harmonics from these signals as shown in Fig. 5 and Fig. 6. The filtered current and voltage signals (Ipv_F and Vpv_F) are then fed into the MPPT control block that uses the Incremental Conductance Tracking Algorithm. An algorithm that is based on the fact the slope of the PV array power curve shown in Fig. 7 is zero at the Maximum Power Point (MPP), positive on the left of the MPP, and negative on the right. The MPP can thus be tracked by comparing the instantaneous conductance (I/V) to the incremental conductance (∆ I/∆ V) [11] as in (1):
    2013-07-23 17:56:06下载
    积分:1
  • ViolaJones_version0b
    matlab code for Viola Jones Object Detection
    2015-02-07 14:24:16下载
    积分:1
  • 696518资源总数
  • 104432会员总数
  • 16今日下载