-
STM32+ESP8266+SHELL
STM32加ESP8266模块，实现UDP透传模式通信，可以通过SHELL命令，获取采集电压和时间信息。在UDP调试工具输入“getcfg”可以获取配置信息 包括单次测量模式 循环测量模式 循环时间间隔设定等等相关参数设置。(STM32 and ESP8266 module are used to achieve UDP transmission mode communication, and the acquisition voltage and time information can be obtained through the SHELL command. In the UDP debugger, input "getcfg" can get configuration information, including single measurement mode, cycle mode, cycle interval setting and so on.)
- 2018-02-10 23:51:58下载
- 积分：1
-
duojitongxin
关于两个单片机之间能够实现多机通信的源代码！内部有。HEX的下载文件，可便于学习版下载！(duojitongxin)
- 2009-11-01 15:25:28下载
- 积分：1
-
实验3 按键输入
正点原子STM32F103精英板按键输入例程(Punctual Atom STM32F103 Elite Board Key Input Routine)
- 2020-06-21 11:20:02下载
- 积分：1
-
11
说明： 利用定时/计数器T0从P1.0输出周期为1s的方波，让发光二极管以1HZ闪烁，设晶振频率为12MHz(The use of timer/counter T0 from P1.0 output cycle square wave 1s, so that the light-emitting diodes 1HZ blinking, set the crystal frequency is 12MHz)
- 2014-05-27 14:30:43下载
- 积分：1
-
chengxu
基于LabWindows/CVI的炉温控制系统的源程序开发，可以对温度进行实时监控和快速调整。(Based on LabWindows/CVI furnace temperature control system of the source code to develop, you can conduct real-time monitoring of temperature and rapid adjustment.)
- 2009-06-05 19:30:41下载
- 积分：1
-
c
单片机C语言入门教程，非常适合新手入门。从基础讲起，逐步提高。(Single-chip C Language Tutorial, very suitable for beginners. Start from the base, and gradually improve.)
- 2013-07-18 23:08:42下载
- 积分：1
-
signal-intersection
智能交通单路口C++仿真程序，其中设置了随机车辆产生，以及信号配时功能，程序编译已验证(Intelligent Transportation single intersection C++ simulation program, which is set to generate random vehicles, as well as signal timing functions, the program compiled Verified)
- 2014-03-01 09:39:29下载
- 积分：1
-
555712
梦幻WAS提取源码程序位图的结构，使用置入汇编代码的方法实现提取梦幻WAS资源。(Fantasy WAS extraction structure of the source program bitmap into assembly code using methods to achieve the dream WAS resource extraction .)
- 2015-09-01 12:56:03下载
- 积分：1
-
SLE4428驱动
SLE4428逻辑加密卡驱动程序源码， C语言实现(sle4428 logic encryption card, driver source code, c language)
- 2021-02-03 11:09:59下载
- 积分：1
-
ansys-input-adams1
ansys导入到adams中做刚柔耦合动力学分析，采用的是梁单元，希望对大家做刚柔耦合动力学分析有所帮助(ansys and adams are work together)
- 2013-12-22 15:22:10下载
- 积分：1
