-
lms
目前主流的lms算法实现，采用随机数最为种子。(The current mainstream lms algorithm, using the most random number seed.)
- 2009-10-09 00:21:33下载
- 积分：1
-
QPSKmodulate
该程序仿真了QPSK调制和解调，并给出了详细的说明。(this program simulates the modulation and demodulation of Qpsk，giving details introduction。)
- 2009-12-03 10:27:12下载
- 积分：1
-
Simulated-Annealing-of-matlab-matlab
Simulated Annealing of matlab
- 2013-01-14 11:48:49下载
- 积分：1
-
Uniform-LBP
包括原始LBP、均匀LBP和旋转均匀LBP三种模式的子程序，适合初学者调用研究。(Three commom LBP models for beginners to use.)
- 2015-08-28 17:37:47下载
- 积分：1
-
PID
一个比较典型的PID处理程序，在使用单片机作为控制cpu时，请稍作简化，具体的PID
参数必须由具体对象通过实验确定。由于单片机的处理速度和ram资源的限制，一般不采用浮点数运算，
而将所有参数全部用整数，运算到最后再除以一个2的N次方数据（相当于移位），作类似定点数运算，可
大大提高运算速度，根据控制精度的不同要求，当精度要求很高时，注意保留移位引起的“余数”，做好余
数补偿。这个程序只是一般常用pid算法的基本架构，没有包含输入输出处理部分。
(A typical PID process, using the microcontroller as a control cpu, make some simplification, the specific PID parameters must be determined experimentally by a specific object. As the chip processing speed and ram resource constraints, generally do not use floating-point operations, and all parameters of all integers, and divided by an operator to the last N-th power of 2 data (the equivalent of the shift) for a similar fixed-point operations, can greatly improve the speed of operation, according to the different requirements of precision control, when high precision, attention to retain the shift caused by the " remainder" and on the remainder of compensation. This procedure is commonly used basic structure pid algorithm, does not include input and output processing section.)
- 2011-07-17 23:45:45下载
- 积分：1
-
OS-EM.ps
another NDFT algorithm for signal processing
- 2009-11-18 15:17:20下载
- 积分：1
-
M
说明： MATLAB帮助,很好的初学者教程，很有用(MATLAb help，it is very usefull)
- 2011-06-25 21:05:59下载
- 积分：1
-
INVERTERPWMcompensater
compensation of dead time effect of the inverter dead time effect causes the impact of the control performance of the INVERTER system, and pointed out that the dead time compensation, the key lies in the current phase of the acquisition, in order to overcome the practical zero of the current ambiguity of the system is proposed based on the two-phase stationary coordinate system under the feedforward dead-time compensation method. by the offset voltage of the three-phase output current cycle Fourier transform is found only compensation 1, 5, 7 harmonic components to eliminate the dead time effect. simulation and experimental results verify the correctness and feasibility of this approach.
- 2013-11-11 23:14:37下载
- 积分：1
-
zhifangtu
MATLAB实现均衡算法，画出原始图像的直方图和经过处均衡处理后的直方图(MATLAB realize equalization algorithm, draw the original image s histogram and after treatment, the Department balanced histogram)
- 2007-11-11 13:35:21下载
- 积分：1
-
NonlinearLoadModel2
在MATLAB/simulink下，搭建三相四线制非线性负载。(In the MATLAB/simulink, the three-phase four-wire system to build non-linear load.)
- 2011-01-16 10:12:59下载
- 积分：1
