-
sch
小区初搜为GSM系统中的一个关键过程，本程序为GSM小区初搜过程的第二部，查找同步突发sch并定时的matlab程序，输入数据由采样数据得到，在转换成所需格式后进行处理。若其中包含sch,则输出找到信息，并计算得到定时信息。若没有，则查找下一个突发。内付算法详细说明文档(Area early in the search for the GSM system, a key process, the procedures for the GSM cell the second part of the beginning of search process to find the synchronous burst sch and timing matlab procedures, input data from the sampling data in converted into the required format for processing. If one includes sch, then output to find information and to calculate timing information. If not, then find the next emergency. Pay the algorithm in detail within the document)
- 2008-05-05 20:14:58下载
- 积分：1
-
all
模式识别分类器的设计，此为K均值法源码，经调试通过。所用数据为标准IRIS。(Pattern recognition classifier design, the source for the K-means, after debugging through. Data used as the standard IRIS.)
- 2008-08-12 09:42:28下载
- 积分：1
-
小波变换
说明： 做地震数据处理的去噪程序，通过原始信号，加噪声的信号，以及小波变换的信号进行比较分析，并生成图像。(Do the denoising program of seismic data processing, compare and analyze the original signal, noise signal and wavelet transform signal, and generate the image.)
- 2020-12-12 11:19:17下载
- 积分：1
-
SLM_Papr_V4
“SLM_Papr_V4.m”，SLM方法(V=4)PAPR的互补累积分布函数(CCDF)曲线。(A way to reduce the high PAPR of OFDM system-SLM)
- 2010-07-17 15:03:30下载
- 积分：1
-
控制系统仿真
说明： 基于LQR方法的风电机组变桨距控制的动态建模与仿真分析
模型搭建完成，功率跟踪效果良好(Dynamic modeling and simulation analysis of wind turbine pitch control based on LQR method
The model is built and the power tracking effect is good)
- 2020-05-18 16:14:38下载
- 积分：1
-
getConnectedSize
识别连通区域，在matlab环境中自动识别连通区域的大小。(identify regional connectivity in Matlab environment automatic identification of the size of regional connectivity.)
- 2007-07-06 11:36:07下载
- 积分：1
-
homfilter
hpfilter function for matlab
- 2012-05-15 23:16:37下载
- 积分：1
-
m
说明： IIR filter implementation DFT
- 2015-04-19 01:03:17下载
- 积分：1
-
case14
本程序采用的是基于matlab的PQ分解法潮流计算，程序主要分为三个部分：第一部分用于生成系统的节点导纳矩阵。第二部分主要进行潮流系统的迭代运算。第三部分主要用于对程序最后输出结果的计算，如电压的幅值，相角，功率分布等。(This procedure is used in matlab the PQ decomposition method based on flow calculation, the program is divided into three parts: The first part of the node admittance matrix used to generate the system. The second part of the iteration trend system. The third part is mainly used for the calculation of the final output of the program, such as the amplitude of the voltage, phase angle, power distribution.)
- 2016-04-27 10:05:18下载
- 积分：1
-
Decomp
用于将地震的矩张量分解为DC/CLVD/ISO三种，对于研究地震的人士很有用的(program for a decomposition of moment tensors into the DC, CLVD and ISO)
- 2020-12-01 16:09:26下载
- 积分：1
