登录
首页 » C++ » menu

menu

于 2012-11-28 发布 文件大小:1KB
0 70
下载积分: 1 下载次数: 2

代码说明:

  这是一个点菜菜单,是个用C语言来编程实现的菜单形式。(This is an a la carte menu is a menu form using C language programming.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 5956444spwm20170327
    脉宽调制,亲自调试通过,是一个很好学习的资料(Pulse width modulation, self-testing, is a very good learning material.)
    2020-06-17 04:40:01下载
    积分:1
  • MLX90614_430
    MLX90614_430非接触式红外温度传感器,代码亲测有效可用正常使用 MSP430G2553(MLX90614_430 non-contact infrared temperature sensors, the code effective pro-test available normal use MSP430G2553)
    2020-10-03 15:17:40下载
    积分:1
  • RTD2660_AV1_AV2_131015
    RTD2660 RTD2660H 源码 可点TTL LVDS屏 可做AV VGA DVI HDMI接口(RTD2660 RTD2660H source point TTL LVDS screen can do the AV VGA DVI HDMI Interface)
    2015-09-23 15:41:36下载
    积分:1
  • 10程序和原理图
    说明:  伺服电机驱动器的原理图和DSP程序,是原厂的一手技术资料,成熟方案,对于研究伺服驱动器的有重大研究价值。(The schematic diagram and DSP program of the servo motor driver are the first-hand technical data of the original factory. The mature scheme is of great research value for the research of the servo motor driver.)
    2020-06-18 21:58:00下载
    积分:1
  • s3c2440芯片中文手册
    说明:  友善之臂MIni2440开发板官方光盘文件(Friendly Arm MIni2440 Development Board Official CD)
    2019-04-05 10:31:54下载
    积分:1
  • STM32103制作的数控电源源代码
    说明:  用STM32103单片机,采用数码管显示电流、电压的数控电源。对学习STM32单片机编程和DIY数控电源很有实用价值。(With STM32103 single chip microcomputer, digital tube is used to display current and voltage. It is very useful for learning STM32 single chip computer programming and DIY numerical control power supply.)
    2020-03-10 22:21:20下载
    积分:1
  • duoji_led
    键盘控制舵机同时会让led闪烁,适合慧净HL-1的初学者,但是没有注释(Keyboard control steering gear at the same time will make the led flashing, is suitable for the beginners, hui net- HL 1 but there is no comment)
    2015-08-11 17:34:25下载
    积分:1
  • main
    MSP430 触摸板控制lED程序,看门狗实例程序,(MSP430 touch)
    2014-10-27 15:40:44下载
    积分:1
  • 新建文件夹 (2)
    说明:  实验二定时发送程序:复位后,发送板每个大约一秒时间利用CAN总线向接收板发送一个数据(值为发送板数码管显示值),按下按键1,可以暂停或启动发送。 发送板数码管显示值每隔大约一秒增加一(不管按键是否暂停向接收板发送数据)。接收板收到CAN总线接收的值显示在数码管上,初始为0。(Experiment 2 timing sending program: after reset, the sending board USES CAN bus to send a data (the value is the display value of the digital tube of the sending board) to the receiving board for about one second each. Press key 1 to pause or start sending.The display value of sending board digital tube increases by one every about one second (regardless of whether the button is paused to send data to the receiving board).The value received by the CAN bus by the receiving board is displayed on the nixie tube with the initial value of 0.)
    2020-06-20 11:00:02下载
    积分:1
  • duandianshizhong
    一个断电延时时钟,芯片为1302 液晶1602(A power-off delay clock, chip LCD 1602 1302)
    2011-11-21 17:37:49下载
    积分:1
  • 696522资源总数
  • 104040会员总数
  • 35今日下载