登录
首页 » Unix_Linux » src

src

于 2013-12-19 发布 文件大小:30KB
0 171
下载积分: 1 下载次数: 13

代码说明:

  103转modbus协议C程序,支持多个485端口并能够配置(103 turn modbus protocol C program, more than 485 ports and supports the ability to configure)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 4867537666
    百度手机地图 实例集合,应用程序编程源码,很好的参考资料。(Set Baidu mobile phone map example, application programming source code, a good reference.)
    2013-11-12 00:06:06下载
    积分:1
  • matlab_exercise_6_081212
    Matlab in German Course
    2009-11-11 08:04:29下载
    积分:1
  • STC单片机多机联级串口序可实现.416路控制
    说明:  STC单片机多机连级串口程序可实现.416路控制. 串口和485都可以使用、 一个程序可以用在26块控制板上,通过拔码开关给板子编号,每块板可以过滤分析所接收到不同的代码。进行继电器的动作,能返回数据,因使用定时器发送返回,不会阻塞或者代码错乱、可以 用在中控,物联网,等各种控制场合。修改代码后,能达到上千路的控制。(STC single-chip microcomputer multi-level serial port program can realize 416 channel control. Serial port and 485 can be used. One program can be used on 26 control boards. Each board can filter and analyze different codes received by numbering the boards with the pull-out switch. Relay operation can return data, because the timer is used to send the return, it will not block or code confusion, and can be used in central control, Internet of things, and other control occasions. After modifying the code, it can achieve thousands of control.)
    2020-03-06 23:07:17下载
    积分:1
  • 4up-SensorNetHW
    Wireless Sensor Network (WSN) Platforms
    2009-09-07 02:04:31下载
    积分:1
  • RayleighFading
    瑞利多径衰落信道仿真,jakes模型,有图(rayleigh fading)
    2013-11-05 20:57:46下载
    积分:1
  • BER
    这是一个matlab和optisystem联合调试用的误码率计算程序,里面的文件报过一个可以用optisystem7和optisystem13可以打开的OSD仿真图,还有一个MATLAB计算BER的程序。给出了如何设置系统的大纲。从OptiSystem的电信号输入到Matlab组件。当OptiSystem运行时,它将调用Matlab组件中的M文件,处理数据,然后将所得的电信号导出回OptiSystem。然后将输出信号连接到BER分析仪。经过我调试,文件齐全,放心下载(The attached image gives an outline of how the system should be setup. You should start with inputting the electrical signal from OptiSystem into a Matlab component. When OptiSystem runs, it will call the M-file in the Matlab component, process the data, and then export the resulting electrical signal back into OptiSystem.The output signal is then connected to the BER Analyzer.)
    2021-03-18 15:39:20下载
    积分:1
  • 33356
    运用labview开发环境,实现串口通讯,接受串口发送接收的数据(Development environment using labview, serial communications, sending and receiving serial data received )
    2012-01-09 10:30:09下载
    积分:1
  • nonlinear-PAPR
    基于非线性压扩的降低OFDM信号PAPR的算法(Reduction based on nonlinear companding algorithm for OFDM signal PAPR)
    2021-04-22 11:28:48下载
    积分:1
  • MIMO-capacity-research
    本程序分析了MIMO系统中发射天线数目对系统容量的影响(This program analyzes the MIMO system, the number of transmit antennas of the system capacity,)
    2013-08-15 15:30:55下载
    积分:1
  • ls 与 mmse 两种信道估计算法比较LS_MMSE
    说明:  ls 与 mmse 两种信道估计算法比较(Comparison of LS and MMSE channel estimation algorithms)
    2020-09-15 14:47:56下载
    积分:1
  • 696518资源总数
  • 104269会员总数
  • 42今日下载