-
chap11
说明： 本目录主要包括：文档和两个源代码。
其中一个源代码是识别程序的，另一个是一个矩阵类库的，书里面也使用过，所以一并附上。
因为已经保存了训练好的网络权值，所以第一次使用识别程序时，可以直接运行\\Release目录下的可执行文件，然后对图片目录中的测试图片进行读入、识别。
当然读者也可以自行用训练样本训练网络，不过要特别注意训练样本的选择，否则可能造成识别率很低。训练样本选择的原则是，尽可能的有代表性，在训练时间不至于太长的情况下，训练样本数目尽量多。
( This directory includes: documentation and two source code.
One of the source code is to identify the procedure, the other is a matrix class library, the book which is also used, so be attached.
Because it has saved the trained network weights, so the first use of identification procedures, you can directly run \ \ Release directory of the executable files, and then tested on the images directory to read pictures, identification.
Of course, readers are free to use the training samples to train the network, but pay special attention to training samples, otherwise it may cause very low recognition rate. Training sample selection principle is that as far as possible, representative, in the long training time Buzhi Yu s case, the number of training samples as much as possible.
)
- 2010-04-11 22:26:09下载
- 积分：1
-
arc_polygon3dm
南极三维坐标转换算法,三维平面坐标系到极方位等角坐标系(3d coordinate system transform of antarctic)
- 2011-05-24 01:02:58下载
- 积分：1
-
blackman0
用布莱克曼窗设计FIR滤波器，不错的程序，大家可以参考(FIR filter with Blackman window design, a good program, you can refer to)
- 2010-06-02 19:43:57下载
- 积分：1
-
Mod_Mas
programme de simulation MAS
- 2011-07-16 19:44:46下载
- 积分：1
-
TQI
根据轨道不平顺的实测数据进行TQI值的计算统计分析(TQI value is calculated according to a statistical analysis of the measured data track irregularity)
- 2021-04-21 17:28:49下载
- 积分：1
-
Fuzzy-logic-C-a-matlab-code
Fuzzy logic C & matlab code
- 2011-11-10 11:40:11下载
- 积分：1
-
exclass3
svm分类程序，经过调试，对初学者很有用的(svm classification procedures, after debugging, useful for beginners)
- 2011-11-21 16:45:54下载
- 积分：1
-
article
软件程序按照发射端所掌握的各用户信道状态信息的程度共分为两部分：即完整信道状态信息(CSIT)和部分信道状态信息(CSIP)。其中，每一部分都包括预编码(precoding)和用户调度(scheduling)
在CSIT中，precoding又按照各用户的数据流数分为单数据流和多数据流两种情况。在每种情况下，首先考察了不同预编码算法的性能表现，包括两种ZF、MMSE、SINR、SLNR。之后又考察了功率分配算法的性能表现（文件名中含有PD表明其含有功率分配的过程）。按照不同指标进行功率分配的，在文件名中进行了区分，如PD_CN代表以信道范数为参考指标进行功率分配。Scheduling部分首先观察了RoundRobin、MaxH和MMSLNR三种算法的性能对比。之后在Kc和Round部分分别观察了不同预选用户数和不同最大替换轮数下MMSLNR算法的表现。
在CSIP中，只对各用户单数据流的情况进行了仿真。采用的预编码算法主要有DSLNR（即直接运用CSIT下的预编码算法）、ESLNR（即对SLNR进行均值计算的，在CSIP中，引入均值计算的与SLNR有关的算法，其文件名中都有modified以示区别）、EMMSE（即陈明老师那边的那篇文章中的预编码算法）。Scheduling中也只是简单的观察了RoundRobin、MaxH、DMMSLNR和EMMSLNR（前者没有均值计算，后者有）的性能对比。(The degree of channel state information for each user software program in accordance with the master transmitter consists of two parts : the complete channel state information (CSIT) and partial channel state information (CSIP). Wherein , each of which comprises a pre- coding (precoding) and the user scheduling (scheduling)
In CSIT in , precoding and each user according to the number of data streams into a single data stream and multiple data streams in both cases . In each case , first examine the performance of different pre- coding algorithm, including two ZF, MMSE, SINR, SLNR. After they inspected the power allocation algorithm performance ( file name contains PD showed that it contained power allocation process ) . According to different indicators for power distribution , make a distinction in the file name , such as PD_CN representative channel norm-referenced index for power distribution . Scheduling section first observed the performance comparison RoundRobin, MaxH and MMSL)
- 2021-02-04 15:29:58下载
- 积分：1
-
BDhuang
说明： 多通道和单通道接收到的北斗信号数据，利用接收到的北斗数据（.dat .txt文件），进行解析，得到初始伪距，平滑伪距，载波相位，并计算其标准差，并画图。(The Beidou signal data received by multi-channel and single channel are analyzed by using the Beidou data (. Dat. TXT file). The initial pseudo range, smooth pseudo range and carrier phase are obtained, and the standard deviation is calculated and plotted.)
- 2019-11-26 15:18:24下载
- 积分：1
-
redresor-mono
redresor mono, pictures, matlab simulation
- 2011-05-27 18:28:21下载
- 积分：1
