-
ADC1_TriggerConversion
根据对应的按键值，对应输出相应的电容值，并做掉电检测(According to the corresponding key value, corresponding to the output of the corresponding capacitance values and do brownout detection)
- 2013-11-26 23:42:16下载
- 积分：1
-
自创简易示波器
简易示波器双通道，tim adc dma(Simple oscilloscope dual channel, Tim ADC DMA)
- 2019-04-02 16:55:10下载
- 积分：1
-
18B20
51单片机，结合DS18B20温度传感器，实现对温度的采集，通过数码管显示(51 single-chip, combining DS18B20 temperature sensors, temperature acquisition, through a digital display)
- 2016-05-01 13:53:13下载
- 积分：1
-
lex_weight
lexical analysis of text detail program...
- 2009-11-13 05:34:53下载
- 积分：1
-
c8051uart
这是一个基于C51的软件模拟串口程序，希望对大家有用。(This is a C51-based simulation software serial procedures in the hope that useful.)
- 2011-08-03 17:25:11下载
- 积分：1
-
correct-disparity
文章包含视差检测、视差校正、视差评估等内容(disparity detection, disparity correction, disparity evaluation)
- 2011-02-07 23:32:32下载
- 积分：1
-
Inverter-4.5KW
4.5kW逆变电源的原理图和PCB文件（包含控制板、辅电电路和主电路）控制芯片为TDS1093(schematic and PCB documents (including control panel, auxiliary electric circuit and main circuit) of 4.5 kW inverter whose control chip is TDS1093)
- 2015-12-22 16:33:12下载
- 积分：1
-
12864
基于51单片机，12864液晶整屏滚动显示，动态显示(Based on 51 single-chip, full-screen scroll 12864 LCD display, dynamic display)
- 2008-12-14 15:41:10下载
- 积分：1
-
最终版跷跷板
说明： 本实验开机后，先初始化MPU6050，然后利用DMP库，初始化MPU6050及使能DMP，最后，在死循环里面不停
读取：温度传感器、加速度传感器、陀螺仪、DMP姿态解算后的欧拉角等数据，通过串口上报给上位机（温
度不上报），利用上位机软件（ANO_Tech匿名四轴上位机_V2.6.exe），可以实时显示MPU6050的传感器状
态曲线，并显示3D姿态，可以通过KEY0按键开启/关闭数据上传功能。同时，在LCD模块上面显示温度和欧拉
角等信息。DS0来指示程序正在运行。另外,本例程也可以通过USMART调用MPU_Read_Byte/MPU_Write_Byte
等函数,来实现对MPU6050寄存器的读写操作(仅在UPLOAD OFF状态下).(This experiment starts with initializing MPU6050, then using DMP library, initializing MPU6050 and enabling DMP. Finally, it keeps on in the dead cycle.
Read: temperature sensor, accelerometer, gyroscope, Euler angle after attitude calculation of DMP and other data, report to PC through serial port (temperature).
The sensor of MPU6050 can be displayed in real time by using the upper computer software (ANO_Tech anonymous four-axis upper computer_V2.6.exe).
The state curve and 3D posture can be displayed, and the data upload function can be turned on/off by KEY0 button. At the same time, temperature and Euler are displayed on the LCD module.
Angle and other information. DS0 to indicate that the program is running. In addition, this routine can also call MPU_Read_Byte/MPU_Write_Byte through USMART
Equivalent function to achieve the read-write operation of MPU6050 registers (only in UPLOAD OFF state).)
- 2020-06-24 18:40:02下载
- 积分：1
-
PiCAN-Python-examples
说明： 树莓派SPI转CAN，利用MCP2515模块，进行CAN通讯，分开两个.py代码：TX（发送）和RX（接收）的，具体的GPIO口要在代码里自行修改为实际的PI通讯引脚。(Raspberry Pi SPI to CAN, using MCP2515 module, for CAN communication, separate two .py codes: TX (send) and RX (receive), the specific GPIO port should be modified in the code to the actual PI communication pin.)
- 2020-06-17 23:00:02下载
- 积分：1
