登录
首页 » matlab » 4

4

于 2015-04-02 发布 文件大小:11KB
0 65
下载积分: 1 下载次数: 0

代码说明:

说明:  Write a program in MATLAB for edge detection

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • paper_4
    this is a ducument about speech recognition
    2012-05-16 20:01:12下载
    积分:1
  • HW4
    产生母婴心电信号图,程序简单易懂, 欢迎分享下载(Maternal and baby ECG signal, simple one,hope can help somebody)
    2011-11-07 01:36:53下载
    积分:1
  • single_carrier_networks
    单频网的链路级Matlab仿真程序,直接运行可得到误符号率。(Link level simulator for single carrier networks,The simulator outputs symbol error rate.)
    2010-09-14 18:46:54下载
    积分:1
  • matlab001-redcrusader
    this is basic matlab explanation. i will upload 5documents.
    2011-01-13 12:51:37下载
    积分:1
  • jt_matlab6.5
    张志勇的《精通MATLAB6.5》内容详细,是学习MATLAB编程人员值得参考的一本好资料。(Zhang Zhiyong, a " master MATLAB6.5" detailed and is worth considering to learn MATLAB programming staff of a good information.)
    2011-09-03 16:29:29下载
    积分:1
  • flight-dynamics-matlab-model
    大气层内航天器飞行动力学matlab仿真模型(The atmosphere inside the spacecraft flight dynamics matlab simulation model)
    2012-08-24 08:34:10下载
    积分:1
  • GM
    灰色模型在很多行业领域内得到广泛的应用,程序采用MATLAB编程,可实现GM(1,1)预测(Gray model has been widely used in many industries, the program using MATLAB programming, GM (1,1) prediction)
    2013-05-20 14:53:03下载
    积分:1
  • 10.1007_978-3-642-25486-4
    Generating manipulator trajectories considering multiple objectives with kinematics and dynamics constraints is a non-trivial optimization. In this paper, a constrained multi-objective genetic algorithm (MOGA) based technique is proposed to address this problem for a general motor-driven parallel kinematic manipulator.(生成机械手轨迹考虑  多个目标的运动学和动力学约束是一个简单的优化。在本文中,  约束多目标遗传算法  )技术提出了解决这一问题 问题一般电机驱动的平行运动操纵者。)
    2014-06-24 16:00:27下载
    积分:1
  • stabilityfactor
    研究1维FDTD的收敛情况,分情况讨论stability factor小于,大于,等于1的情况(The convergence of one-dimensional FDTD case, the situation points to discuss stability factor is less than, greater than, equal to 1)
    2011-09-22 11:19:30下载
    积分:1
  • BSpline
    程序实现二次B样条平滑,三次B样条平滑;二次B样条平滑后节点插值(Program to achieve the second B-spline smoothing, cubic B-spline smoothed after the second B-spline interpolation smooth node)
    2014-12-07 23:00:29下载
    积分:1
  • 696519资源总数
  • 104213会员总数
  • 20今日下载