-
信捷PLC通讯
用于信捷PLC与Labview之间的通信，可以作为学习的初版(Used for the communication between Sinjie PLC and Labview, it can be used as the first edition of learning.)
- 2020-06-21 15:00:02下载
- 积分：1
-
Delete
说明： Labview环境下删除数组中重复元素而不改变原数组元素排列顺序(Labview environment, remove duplicated elements in the array without changing the original order of the array elements)
- 2010-03-19 21:36:35下载
- 积分：1
-
chufa
（2） 发生一个值为0.0~10.0之间的随机数，并除以一个在前面板中输入的数。如果输入的数为0，则点亮LED，提示除数为0时，除法无效。((2) a value of 0.0 to 5.0 occurred between random numbers and dividing by a number entered in the front panel. If the input is 0, then lit LED, prompted the divisor is 0, the division is invalid.)
- 2013-10-29 23:31:33下载
- 积分：1
-
Labview_DLL
Labview 实现调用动态链接库 有详细说明 程序案例和与案例说明 是学习的好材料！(Labview implementation calls the dynamic link library procedures are described in detail with examples and case notes are a good learning materials!)
- 2014-12-12 12:58:11下载
- 积分：1
-
虚拟示波器
说明： Labview虚拟示波器程序，编程入门提高(LabVIEW virtual oscilloscope program, programming to improve the entry)
- 2020-09-16 11:05:22下载
- 积分：1
-
yuyincaijixitong
基于labview的语音采集系统，可以进行录音等操作。为北京理工大学实验课结课作业。(Labview-based voice acquisition system, recording and other operations can be performed. Experimental course for the Beijing Institute of Technology knot class job.)
- 2013-10-20 22:25:51下载
- 积分：1
-
labview读取EXCEL数据
说明： 可以通过labview读取excel中的数据，可将excel中的数据写入到labview.(The data in excel can be read through labview, and the data in excel can be written into labview.)
- 2019-10-01 20:40:37下载
- 积分：1
-
用于控制keithley2600数字源表测量太阳电池的IV曲线 IV-curve-measure-with-Keithley2600
该程序可用于控制keithley2600数字源表测量太阳电池的IV曲线。可设置正反扫描次数，实时显示测量结果，并计算Jsc，Voc，FF，eff等电池参数。程序IVnew是总程序，除子程序外，还包括NI公司网站上提供的keithley2600程序包（必要）。(The program can be used to control keithley2600 digital source meter to measure the solar cell IV curve. Can be set to the number of positive and negative scanning, real-time display of measurement results, and calculate the cell parameters of Jsc, Voc, FF, eff. The program ‘IVnew’is the final program.)
- 2020-06-28 10:20:01下载
- 积分：1
-
LabVIEW-point-line-meter
利用Matlab的图象处理功能对摄象头采集到的仪表图象进行分析,得到指示值,同时利用dll 技术,在虚拟仪器编程软件Labview 中调用,输出得到对应的计算值,实现了对指针式仪表的自动监控,增加了整个系统的稳定性和可靠性。(Using Matlab image processing functions on the image pickup head collected instrument image analysis, to give the instruction value, while using dll technology, called the virtual instrument programming software LabVIEW, obtained from the output corresponding to the calculated value, the pointer Instrumentation automatic monitoring, increasing the stability and reliability of the whole system.)
- 2013-02-21 16:56:19下载
- 积分：1
-
Time-domain-analysis-system
本系统可做自动控制原理中的时域分析仿真实验，系统特性如下：
1：可选择仿真系统为一阶、二阶、任意阶
2：可选择信号源为正弦波、三角波、锯齿波、方波（可模拟阶跃信号），并可调节信号源频率、幅值、相位、偏移、方波占空比
3：可选择信号采样率及采样数
4：自动计算传递函数
5：自动计算时域响应参数（增益系数、上升时间、峰值、峰值时间、稳定时间、超调量）
6：波形图同时显示原始信号和响应信号
注：使用本系统需安装labview控制设计与仿真库(The system can do automatic control theory in the time-domain analysis simulation, the system behaves as follows: 1: simulation system can be selected for the first, second, any order 2: select the signal source is a sine wave, triangle wave, sawtooth, square wave (analog step signal), and can adjust the signal source frequency, amplitude, phase, offset, duty cycle square wave 3: the the optional signal sampling rate and the number of samples 4: automatic calculation of the transfer function 5: Automatic calculation domain response parameters (gain coefficient, rise time, peak, peak time, settling time, overshoot) 6: waveform diagram shows both the original signal and the response signal Note: Use the system to be installed LabVIEW Control Design and Simulation library)
- 2013-05-12 11:53:34下载
- 积分：1
