登录
首页 » matlab » XUni

XUni

于 2013-04-27 发布 文件大小:153KB
0 66
下载积分: 1 下载次数: 52

代码说明:

  PWM整流器,虚拟电网磁链定向的控制方式论文.(PWM rectifier, the virtual grid flux oriented control mode papers.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论


0 个回复

  • spacevector
    matrix converter simulation in simulink
    2010-08-28 20:34:47下载
    积分:1
  • Inventory
    code of the inventory project
    2015-02-06 14:32:50下载
    积分:1
  • Bangkok
    travel guide to bankok
    2010-11-01 20:27:49下载
    积分:1
  • Watermark_DCT
    watermarking using dct
    2015-04-08 05:44:28下载
    积分:1
  • pkyujjvb
    给出了kalman、RLS、LMS三种自适应滤波器的仿真matlab程序,在ImeQHEw环境下调试,三种滤波器都采用了10次迭代,平均ObXIODw参数性能良好,将仿真值与理论值进行了比较。(Given the Kalman and RLS and LMS three adaptive filter matlab simulation procedures, in the ImeQHEw environment debugging, three kinds of filters using the 10 iterations, average ImeQHEwl parameters with good performance, simulation value was compared with the theoretical value..)
    2016-02-16 20:29:44下载
    积分:1
  • leach
    leach协议分簇算法,能量消耗,死亡节点数,轮数,MATLAB仿真程序,欢迎下载(Leach protocol clustering algorithm, energy consumption, number of dead nodes, number of rounds, MATLAB simulation program, welcome to download)
    2019-04-03 19:37:53下载
    积分:1
  • cankaoMLS
    自适应滤波的源代码,根据你的情况,稍作改动,即可使用,非常好用(Adaptive filtering the source code, depending on your situation, make a little change, you can use, very easy to use)
    2011-04-30 10:00:29下载
    积分:1
  • Analysis-of-the-kinematics
    连杆机构的运动分析,曲柄滑块机构的运动学分析(Analysis of the kinematics of the slider-crank mechanism)
    2012-07-08 08:46:44下载
    积分:1
  • GA
    说明:  在考虑汽车零部件包装箱长、宽、高等三维尺寸的约束下,以配送中心为原点,分派多辆同一规格的货车到n个供应商处取货,最后回到配送中心。本章所构建的三维装载约束下的汽车零部件循环取货路径优化模型要解决的问题是确定循环取货路径,要求充分考虑汽车零部件在货车车厢中的三维装载位置,确保每个供应商处的零部件均能成功装载,尽可能使车辆装载率最大,且所有车辆的总行驶路径最短。(In considering the auto parts box length, width, higher dimensional size constraints to the distribution center as the origin, a multi-vehicle dispatch trucks to the same specifications of the pick n suppliers, and finally back to the distribution center. Auto Parts Pick cycle path constructed three-dimensional loading constraints under chapter optimization model to solve the problem is to determine the circulation pickup path requires full consideration in boxcars loaded in three-dimensional position of auto parts, to ensure that each vendor Parts can successfully loaded, as the vehicle maximum loading rate, and the total of all vehicles traveling the shortest route.)
    2015-04-20 15:48:48下载
    积分:1
  • truss_static
    编写了利用MATLAB计算任意桁架的静力分析,得到各杆的应力和各结点的位移,并画出变形前后的桁架图(The static analysis of arbitrary truss is made by using MATLAB, the stress of each rod and the displacement of each node are obtained, and the truss diagram before and after deformation is drawn)
    2021-04-25 11:18:46下载
    积分:1
  • 696518资源总数
  • 104271会员总数
  • 57今日下载