-
PT100_STC1256xxAD
STC1256xxAD系列MCU实现8路PT100温度巡回检查程序，温度过高或过低报警。(STC1256xxAD Series MCU achieve 8 PT100 temperature roving inspection procedures, high or low temperature alarm.)
- 2014-02-22 15:46:37下载
- 积分：1
-
dq_transform
dq变换法程序,用于电能质量的监测和有功电流或无功电流的计算等。(dq transform procedures for power quality monitoring and active current or reactive current calculation.)
- 2007-10-01 20:09:50下载
- 积分：1
-
LabVIEW_PID_Design_Source_Code
附件为LabVIEW的vi程序和说明文档。描述：利用LabVIEW2012设计PID控制器，利用PID工具包，在LabVIEW仿真工具包中的控件与仿真循环中搭建PID控制器,并实现了闭环控制系统波形图的显示。(Attachments are the LabVIEW vi program and the documentation for PID controller design. The program includes the PID controller constructing and the closed-loop system output display.)
- 2013-12-13 14:43:19下载
- 积分：1
-
CardTool-
ACR38智能读卡器测试用：芯片IC卡等(ACR38 Smart Card Reader test: IC card, etc.)
- 2020-12-04 08:49:25下载
- 积分：1
-
Client
本文以霍尔茨(HOLZER)法作为船舶轴系扭转振动的计算方法，着重研究了船舶轴系自由扭振的计算与分析，并对轴系扭振产生原因进行了分析，提出了一系列减振方法，以保证船舶动力装置的安全正常运行。(In this paper, Holtz (HOLZER) Act as the ship shafting torsional vibration calculation methods, focusing on the calculation and analysis of ship shafting torsional vibration of freedom, and the shaft torsional vibration causes analyzed, proposed a series of less vibration methods to ensure the safety of the ship s power plant running.)
- 2014-07-23 10:04:16下载
- 积分：1
-
串口显示字符串
说明： 51单片机18b20采集温度，串口打印显示温度值，(51 single chip computer 18B20 collects temperature, and serial port prints and displays temperature value.)
- 2020-06-21 20:20:01下载
- 积分：1
-
Chip-electronic-bell-million-years
单片机万历年电子钟Chip electronic bell million years(Chip electronic bell million years)
- 2013-11-15 15:16:49下载
- 积分：1
-
STM32+RC522+充值+扣款+改密码+开锁
说明： STM32+RC522+充值+扣款+改密码+开锁(STM32 + rc522 + recharge + deduction + change password + unlock)
- 2021-03-07 18:59:29下载
- 积分：1
-
ADC
利用cc2430自带的adc实现模数转换(Achieved by cc2430 own adc analog to digital conversion)
- 2011-01-08 20:07:38下载
- 积分：1
-
Vacuum-pumping-speed-graph
真空机组先启动SK-30水环真空泵带压力降到6.5 KPa（此时真空机组的抽速是SK-30的抽速）启动ZJP-1200（此时真空机组的抽速是ZJP-1200抽速）待压力降到4 KPa启动ZJP2500（此时真空机组的抽速是ZJP-2500抽速）待压力降到1kpa时最后启动ZJP5000（此时真空机组的抽速是ZJP-5000抽速）到100Pa达到使用真空度时时就可以关闭机组(Vacuum unit first start SK-30 water ring vacuum pump with pressure drops below 6.5 KPa (pumping speed of the vacuum unit at this time is SK-30 pumping speed) start ZJP-1200 (pumping speed of the vacuum unit at this time is ZJP-1200 pumping speed ) until pressure drops below 4 KPa start ZJP2500 (pumping speed of the vacuum unit at this time is ZJP-2500 pumping speed) until the last start when pressure drops 1kpa ZJP5000 (pumping speed of the vacuum unit at this time is ZJP-5000 pumping speed) to 100Pa achieved using vacuum unit can be closed from time to time)
- 2020-11-09 10:29:47下载
- 积分：1
