登录
首页 » matlab » Codice

Codice

于 2013-12-07 发布 文件大小:17KB
0 100
下载积分: 1 下载次数: 1

代码说明:

  经典MATLAB算法,插值计算,拟合,绘图等(Classic MATLAB algorithms, interpolation, fitting, drawings, etc.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Speech-Processing-using-MATLAB
    speech signal processing toolbox
    2012-05-15 01:33:59下载
    积分:1
  • segitiga-matlab
    this is to make a triangle wave in matlab
    2013-09-11 10:04:23下载
    积分:1
  • ActivePhotonics
    VPI simulation Active Photonics
    2012-09-21 05:45:49下载
    积分:1
  • spline
    matlab小波变换源代码,供广大研究者学习(matlab wavelet transform source code, for the majority of researchers to learn)
    2013-11-22 21:37:29下载
    积分:1
  • Tkalfilterh
    标准的卡尔曼滤波程序,使用matlab实现,程序中通通过一个简单的模拟,说明了卡尔曼滤波器的跟踪滤波原理。 (Standard Kalman filtering procedures, the use of Matlab implementation, pass through a simple simulation program, the Kalman filter tracking filter principles.)
    2012-08-12 00:15:02下载
    积分:1
  • gray
    灰色预测模型,已在软件上调试通过,用户需要自定义一个data文件(gray model)
    2012-09-10 11:22:49下载
    积分:1
  • hkbu2005
    介绍了构造均匀设计表的好格子点算法与生成原理,以中心化偏差为均匀性测度,使用MATLAB编写了生成中心化偏差值最小的均匀设计表的计算机通用程序,通过与文献比较,验证了程序的正确性,得到了更多的均匀设计表(The principle and good lattice points designing uniform design table are introduced,the general MATLAB programs for uniform design table are proposed base on searching the minimum of uniform design table s centered L2-discrepancy. The results shows that the programs are right by comparison of the others.)
    2009-06-13 22:10:26下载
    积分:1
  • local_enhancement
    基于MatLAB的图像的局部增强。采用梯度比较,将暗的区域变亮(local enhancement)
    2010-07-14 20:06:18下载
    积分:1
  • kaerman-weina-zishiying
    关于维纳滤波器、卡尔曼滤波器、自适应滤波器的设计方法,及信号提取、分析。(On the Wiener filter, Kalman filter, adaptive filter design method, and signal extraction, analysis.)
    2020-11-05 17:29:50下载
    积分:1
  • 2-Control
    For example, heating up the temperature in a room is a process that has the specific, desired outcome to reach and maintain a defined temperature (e.g. 20°C), kept constant over time. Here, the temperature is the controlled variable. At the same time, it is the input variable since it is measured by a thermometer and used to decide whether to heat or not to heat. The desired temperature (20°C) is the setpoint. The state of the heater (e.g. the setting of the valve allowing hot water to flow through it) is called the manipulated variable since it is subject to control action
    2013-08-16 16:53:45下载
    积分:1
  • 696518资源总数
  • 104349会员总数
  • 32今日下载