-
OPC服务
说明： 自动化领域上位机通过OPC服务读取三菱Q系列PLC的方法(How to read Mitsubishi Q series PLC through OPC service)
- 2020-05-07 08:47:29下载
- 积分：1
-
serial_communication_assistant
matlab GUI编写的串口通信助手，通过一定的串口链接实现PC机之间的串口通信，包括数据的接收和发送。波特率，校验位个数，进制显示，发送周期可以进行设置。(matlab GUI written in serial communication assistant, through certain serial link between the PC serial communication, including receiving and sending of data. The baud rate, parity number, hexadecimal, the the sending cycle can be set.)
- 2012-10-17 16:26:29下载
- 积分：1
-
超级终端_中文_Unicode
XP以后版本，系统已不自带超级终端。
想使用的朋友可以通过单独下载此软件使用。(After the XP version, the system does not have its own super terminal.
Friends who want to use it can download this software separately.)
- 2017-11-15 15:35:16下载
- 积分：1
-
TESTEDLT
说明： 通过cvi实现串口通讯的操作界面：通过RS232串口像下位机发送命令，并采集下位机的数据加以显示. (Serial communication through cvi interface: RS232 serial port through the lower position as to send commands and collect data to lower computer display.)
- 2010-04-11 13:20:43下载
- 积分：1
-
2019.02.24 1400W_SEC
说明： 串口通讯相关的例程，仅供参考，谢谢大家谢谢大家(Serial communication related routines, for reference only)
- 2020-01-08 18:32:21下载
- 积分：1
-
ChuanKouTongXin
Visual Studio下用C#和实现串口通信的完整工程(Implementing Serial Communication using C#)
- 2010-01-04 16:57:40下载
- 积分：1
-
rs232_receiver
RS232接收程序 无奇偶校验位 并行输出8位数据与data_ready数据准备好信号(RS232 receive procedures without parity 8-bit parallel output data and data ready signal data_ready)
- 2009-07-06 19:56:52下载
- 积分：1
-
vb-com
vb 串口上位机 很简单的一个版本，大家自己扩展功能吧
(com executed on pc,it s a simple version ,easy for expansion)
- 2014-01-10 14:22:05下载
- 积分：1
-
SendandReceiveSerial
用Turbo C编写的一个串口操作小程序，能发送，接收信息；程序功能简单，过段时间再把经过修改后的版本传上来(using Turbo C serial prepared by a small operational procedures, send, receive information; Functional procedures simple, then over time, after revision line with the traditional version.)
- 2007-04-23 18:35:17下载
- 积分：1
-
6
说明： 串口通讯实验：
本实验得到的结果为，打开超级终端，设置波特率为115200，数据流控制位为无。运行系统，就会显示“UART & Interrupt Experiment,Please Input from the keyboard”，我们就可以通过写串口操作。
在flash调试时，需要修改RO BASE为0x00000000，其他不用修改，重新编译下载就可运行。
注意：由于系统产生中断，程序计数器就会跳到0x18处执行中断服务子程序，所以不能在SDRAM调试。 (Serial communication experiment: the results of this experiment, open HyperTerminal, set the baud rate to 115200, data flow control bit is not. Operating system, it will display " UART & Interrupt Experiment, Please Input from the keyboard" , we can write the serial port operation. Debug in flash, you need to modify the RO BASE is 0x00000000, the other not modify, recompile download can run. Note: Due to system interrupt, the program counter will jump to 0x18 Department execute the interrupt service routine, it can not debug the SDRAM.)
- 2010-09-01 22:57:00下载
- 积分：1
