-
Diffraction
包含菲涅尔衍射，夫琅禾费衍射和衍射各种传递函数比较，园，十字叉丝，方孔，考扭曲线等的matlab程序(Includes Fresnel diffraction, Fraunhofer diffraction and diffraction comparison of various transfer functions, garden, crossed wires, the hole, twisted lines of matlab test procedures)
- 2011-04-20 15:31:31下载
- 积分：1
-
fdtd3D
3-D FDTD code with PML absorbing boundary conditions(err)
- 2007-12-28 10:42:24下载
- 积分：1
-
Question1
说明： C++源代码，递归实现。原问题描述：鼓上蚤时迁到一个山洞里去盗宝，里面有n件宝贝，价值分别是a1,a2......an，并且满足ai大于a1+a2+....+a(i-1)的和。他身上有一个背包，能装的东西最大价值是K，他只能进洞一次，请问他最多能带出多少？
要求：输入K，n，a1，a2......an
输出：他能最多带出的宝物价值
(C++ Source code Recursive achieve. The original problem description: drum when flea盗宝going to move in a cave, there are n pieces of treasure, valued are a1, a2 ...... an, and to meet ai than a1+ A22B !....+ a (i-1) and. Him to have a backpack, things can hold the greatest value is K, he could only hole once, to ask him to bring out the maximum number of? Requirements: Enter K, n, a1, a2 ...... an output: he can bring out the maximum value of the treasures)
- 2008-12-02 21:07:25下载
- 积分：1
-
mrc_arrraygain
array gain of MRC in a Rayleigh fading channel
- 2013-09-19 20:28:13下载
- 积分：1
-
activeContoursSnakesDemo
本演示实现了主动轮廓模型由Kass等人提出。
要运行它的图形用户界面
1。基于MATLAB型引导提示。
2。关于“到现有的图形用户界面，点击”
3。选择在与本文件相同的目录snk.fig文件
4。按一下上方的绿色箭头启动图形界面
一旦GUI已经启动，您可以通过使用蛇
1。点击“新形象”，并加载输入图像。提供的样品图像。
2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。
3。只要你点击“过滤器”，头发会出现交叉，用他们和你左击鼠标，您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下，你应该单击对象周围的一切你想要的部分。最后一点，必须挑选使用右键单击，以阻止更多的积分为MATLAB的要求。
4。设置各种蛇参数（在能源方面的相对权重的蛇目标函数）或离开它们的默认值，然后按一下他们“迭代”按钮。蛇会出现和移动，因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al.
To run it with GUI
1. Type guide on the matlab prompt.
2. Click on "Go to Existing GUI"
3. Select the snk.fig file in the same directory as this file
4. Click the green arrow at the top to launch the GUI
Once the GUI has been launched, you can use snakes by
1. Click on "New Image" and load an input image. Samples image are provided.
2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image.
3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points.
4. Set the various snake paramete)
- 2010-07-05 11:54:13下载
- 积分：1
-
regiongrowing
区域生长算法，一个老美写的，算法写的相当巧妙，需要花点时间好好看下。(Region growing algorithm, written by an old America, the algorithm is quite clever to write, take time to properly see next.)
- 2010-08-05 17:43:37下载
- 积分：1
-
4DQPSK
π／4DQPSK抗噪声性能仿真与分析,基于扩频和CDMA系统(π/4DQPSK anti-noise performance simulation and analysis, based on spread spectrum and CDMA systems)
- 2009-03-12 00:43:43下载
- 积分：1
-
Oper_Data
PARSING DATA IN MATLAB ALGORITHM
- 2015-03-15 16:29:22下载
- 积分：1
-
timings
说明： 本程序计算1到10000的开根号通过三种不同方法所需要的时间(The program calculates the 1 to 10,000 square root of three different methods by the time required)
- 2011-02-23 14:26:41下载
- 积分：1
-
VCO_best_feedback_Ideal
压控振荡器设计过程的数字计算，无源器件参数(useful programe for the designning of VCO for passive paraameter culculation.)
- 2011-04-21 20:55:40下载
- 积分：1
