-
HassenMIMOOFDM
MIMO-ofdm documents in pdf format
- 2009-05-07 10:26:29下载
- 积分：1
-
ID3
该源码使用ID3算法进行分类，该程序为matlab源码。(Classify using the ID3 algorithm)
- 2012-05-01 15:03:24下载
- 积分：1
-
short-circuit
这个说明倒不是说明函数的功能，只是声明一下函数中出现的问题。
shortest()函数没有问题，在secshortest中我希望只得到一条次短路（或几条roadcost()值相同的次短路），结果却出来好几条，我仔细检查了一下程序，应该没有什么问题。
因此在使用时，要得到次短路，只能用roadcost()函数分别求一下各条路的权重和，找到最小的。
有些奇怪
(Note that this is not the function of function, but a statement about the problems in function. shortest () function there is no problem, I hope that in secshortest only a short time (or several roadcost () times the value of the same short-circuit), the result is several out, I carefully examined the process, it should be no problem. Therefore, in use, to be at a short circuit can only be used roadcost () function, respectively, for some of the weight of the road and find the smallest. Some strange)
- 2009-05-21 21:11:51下载
- 积分：1
-
Initial-alignment
捷联惯导初始对准程序，主惯导与子惯导初始对准(SINS initial alignment procedure, the main INS and sub-inertial alignment)
- 2013-04-11 22:02:29下载
- 积分：1
-
永磁电机滑模观测器模型位置跟踪
说明： 一个永磁同步电动机的滑模观测器仿真模型，可以很好的实现位置跟踪与控制。(A simulation model of sliding mode observer for PMSM can realize position tracking and control well.)
- 2021-03-17 21:49:21下载
- 积分：1
-
sanxiangjiaoliutiaoya
给出了三相交流调压电路在Matlab/simulink下的仿真程序，对毕业设计有帮助。(Three-phase AC voltage regulation circuit is given in the Matlab/simulink simulation under the program, help for graduation.)
- 2010-09-30 13:13:39下载
- 积分：1
-
leach
leach协议matlab代码，很不错的，希望对学习leach协议的同学有帮助。(leach agreement matlab code, very good, I hope to learn leach protocol help students.)
- 2014-01-10 16:57:41下载
- 积分：1
-
matlab_Koch
利用Matlab对Kouch曲线的程序编写，能生成Koch曲线并绘制图形，级数作为外部参数输入，可调整。(The use of Matlab program of Kouch curve to write, can generate Koch curve and graphics rendering, series as external input parameters, can be adjusted)
- 2013-12-09 22:16:41下载
- 积分：1
-
knnclassifier
Knn Classifier used for Various classification purposes
- 2011-05-06 15:15:09下载
- 积分：1
-
MATLABstability_lobe
说明： 针对铣削过程建立的动力学方程，推导出可用以指导加工的稳定性叶瓣图，获得各主轴转速下对应的极限切深。(According to the dynamic equation of milling process, the stable lobe diagram which can be used to guide machining is derived, and the corresponding limit cutting depth of each spindle speed is obtained.)
- 2021-02-01 10:25:54下载
- 积分：1
