-
frft
分数阶傅里叶变换matlab的实现，可以看看的(Fractional Fourier transform matlab realization, you can see the)
- 2013-04-18 14:55:20下载
- 积分：1
-
wuyueshurengongbuwu
无约束连续函数优化的人工鱼群算法通用MATLAB源码.rar
- 2010-08-20 22:01:40下载
- 积分：1
-
main
利用参数辨识法提取相关对准参数，从而估计出陀螺漂移和数学平台偏角并进行补偿。仿真结果表明，开路罗经法对准具有较高的对准精度、较好的快速性，能够满足捷联惯导系统在静基座下实现自对准的要求。(Expressions of mathematical platform misalignment angles of the open-loop algorithm are derived and parameter identification method is
used to pick-up the corresponding coefficients from angle measurements in order to identify and compensate gyro drifts and platform misalignment．The simulation results show that the open circuit gyrocompass alignment of SINS can all meet the requirement of SINS initial alignment with high accuracy and quick reaction on static base. thus can meet the high-precision alignment requirement of carrier based inertial navigation system on swinging base．
)
- 2014-02-09 15:52:36下载
- 积分：1
-
xp165
使用起来非常方便，小波包分析提取振动信号中的特征频率，FIR 底通和带通滤波器和IIR 底通和带通滤波器。( Very convenient to use, Wavelet packet analysis to extract vibration signal characteristic frequency, Bottom-pass and band-pass FIR and IIR filter bottom pass and band-pass filter.)
- 2017-04-17 12:52:50下载
- 积分：1
-
MATLAB_PV
MATLAB很好的仿真里程，包含了很多电子器件仿真，例如DCDC等(MATLAB simulation good mileage, contains a lot of electronics simulation, for example, DCDC, etc.)
- 2015-01-05 15:13:14下载
- 积分：1
-
FPE
说明： 按FPE定阶的
源程序：fpe.cpp
M序列：M序列.txt
白噪声：Gauss.txt
程序中先用依模型阶次递推算法估计模型的参数，再用fpe方法判断模型的阶次。
程序运行结果如下：
n: 1
判断阶次FPE的值: 0.0096406
-0.481665 1.07868
n: 2
判断阶次FPE的值: 0.00875755
-0.446739 0.00498181 1.07791 0.0527289
n: 3
判断阶次FPE的值: 0.0087098
-0.459433 0.120972 -0.0569228 1.07814 0.0390757 0.116982
n: 4
判断阶次FPE的值: 0.000396884
-0.509677 0.4501 -0.200906 0.0656188 1.07991 -0.0156362 0.442989 0.0497236
n: 5
判断阶次FPE的值: 3.2095e-007
-1.18415 0.813123 -0.517862 0.34881 -0.116864 1.07999 -0.744141 0.474462 -0.253112 0.122771
n: 6
判断阶次FPE的值: 3.23349e-007
-1.14659 0.76933 -0.487651 0.329676 -0.10377 -0.00440907 1.07999 -0.703574 0.447253 -0.235282 0.113587 0.00479688
从以上结果可以看出，当n=5时，fpe值最小，所以这时的模型阶次和参数估计值为最优结果：
3.2095e-007
-1.18415 0.813123 -0.517862 0.34881 -0.116864 1.07999 -0.744141 0.474462 -0.253112 0.122771(err)
- 2008-09-12 01:14:14下载
- 积分：1
-
MATLAB7DesktopToolsandDevelopmentEnvironment
MATLAB2009a的教程。使用方法，技巧，新功能等，应有尽有。(MATLAB2009a of course. The use of methods, techniques, new features are now available.)
- 2009-06-09 10:25:30下载
- 积分：1
-
VC_MATLAB
VC + + 与MATLAB 混合编程研究及开发实例(VC++ Mixed Programming with MATLAB examples of research and development)
- 2009-12-20 14:02:02下载
- 积分：1
-
Cqiweibakema_o
设雷达信号是码宽为0.5微妙，中心频率是10MHz的7为巴克码2PSK信号，接收的雷达回波中频采样频率为为40MHz，中频进行正交下变频。假设在13.5km处有一个点目标，仿真该雷达的脉冲压缩处理。 已通过测试。
(Let the radar signal is yards wide 0.5-subtle, the center frequency of the the Buck the code 2PSK signal, the received radar echo IF sampling frequency of 10MHz to 40MHz, IF quadrature down-conversion. Assuming the 13.5km at a point target simulation of the radar pulse compression processing. Has been tested.)
- 2012-07-19 17:33:30下载
- 积分：1
-
Clieduua
计算机械振动烈度，由采集的振振动位移数据来求得可直接使用。
(Calculation of the mechanical vibration intensity, obtained by the vibration vibration displacement data collected can be used directly.)
- 2012-07-24 00:39:57下载
- 积分：1
