-
95302940CAN232B_LabVIEW_Demo
Labview串口只能接受和传递ASCII码,因此你在使用的时候得先把它们转换为ASCII码才行.(Labview serial port can only receive and impart ASCII codes, so you use the time to first convert them to ASCII codes Cai Xing.)
- 2010-01-02 17:47:15下载
- 积分:1
-
excel+fft
本vi用于读取excel文件并将所需数据做快速傅里叶变换(FFT)处理。(This VI is used to read the excel file and to process the required data by fast Fourier transform (FFT).)
- 2017-07-28 11:30:23下载
- 积分:1
-
position control - 09 04 - 副本
电机转速,基于labview。伺服电机控制程序(Motor speed based on LabVIEW. Servo motor control program)
- 2018-05-13 19:10:00下载
- 积分:1
-
asd
航空航天通信技术一般采用模拟通信的频率调制和数字通信的移相键控调制方法。这有利于充分应用信道带宽和能源。频率调制是在一定程度上改变载波或副载波的频率来传输信息的调制方法。移相键控调制是利用载波或副载波的相位跳变来传输信息的调制方法。移相键控又分二相移相键控、四相移相键控和多相移相键控,其中以四相移相键控和八相移相键控调制方法的效率较高(Aerospace communications technology commonly used analog communication of frequency modulation and the digital communication phase shift keying modulation method. This is helpful for making full use of channel bandwidth and energy. Frequency modulation is changed to some extent carrier or subcarrier frequency to transmit information modulation method. Phase shift keying modulation is the use of carrier or subcarrier phase jump to transmit information modulation method. Phase shift keying and binary phase shift keying, four phase shift keying and multiple phase shift keying, of which four phase shift keying and eight phase shift keying modulation method of high efficiency
)
- 2011-07-13 11:21:08下载
- 积分:1
-
tdm example
用MATLAB读取labview监测到到数据波形(Read the data and waveform monitored by LabVIEW with MATLAB)
- 2018-05-20 22:43:11下载
- 积分:1
-
strain-to-deform
这是一个在labview上根据悬臂梁厚,梁长,受力点距固定端的长度,应变片距固定端的长度,以及应变片上的数值来测算梁的最大挠度的程序。(
This is a distance in the labview according thick cantilever beam length, the length of the pitch by the force of the fixed end, the fixed end of the length of the strain gauge and strain values on-chip to measure the maximum deflection of the beam of the program.)
- 2015-09-26 16:32:48下载
- 积分:1
-
Signal Generator
采用Labview设计一虚拟函数信号发生器, 通过数据采集卡输出波形信号,调节信号的相关参数(Labview design using a virtual function signal generator, data acquisition card output waveform signal,)
- 2018-05-25 12:44:20下载
- 积分:1
-
自功率谱VI
自功率谱是分析非平稳信号频谱的重要手段。对于非平稳信号来说,利用自功率谱分析能够更容易找到信号中能量聚集区域,对信号中的频率分布有更好的了解。本文件中将其制作成独立子VI方便程序直接调用。(Self power spectrum is an important method to analyze the spectrum of non-stationary signals. For non-stationary signals, it is easier to find the energy accumulation region in the signal by using self power spectrum analysis, and better understand the frequency distribution in the signal. This document will be made into an independent sub VI convenience program to call directly.)
- 2017-07-29 20:16:16下载
- 积分:1
-
chuankou
说明: 利用Labviewjinxing 串口数据发送接收(Using LabVIEW to send and receive serial data)
- 2021-03-24 15:28:41下载
- 积分:1
-
servovalvetest
一个上位机测控软件,采样Labview2011编写,主要功能的和下位机通信,向下位机下发控制指令,并实时显示处理下位机上传的采集数据。(A PC control software, sampling Labview 2011 write, and communicate the main function of the lower down-bit machine control commands issued, and real-time data acquisition display processing lower computer to upload.)
- 2015-11-09 09:43:53下载
- 积分:1