登录
首页 » matlab » chaos

chaos

于 2014-12-09 发布 文件大小:1KB
0 99
下载积分: 1 下载次数: 25

代码说明:

  混沌信号生成 逻辑映射 三个函数matlab程序(chaos signal)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • jisuan3
    计算CM值,表征系统规整性的一个计算方法(Calculated CM values, characterize the system as a structured method of)
    2010-06-22 10:28:05下载
    积分:1
  • lms1
    说明:  智能天线方向图——波束形成最小均方(LMS)算法(Smart antenna pattern- beam forming least mean square (LMS) algorithm)
    2009-08-26 22:58:46下载
    积分:1
  • yichuansuanfa
    本遗传算法用于目标函数在可行域最优质的寻找情况(The genetic algorithm feasible region for the objective function in the best looking case)
    2015-01-13 19:55:47下载
    积分:1
  • physical_memory
    本文档详细介绍了物理内存的基本内容,并且讲述了内存静态分区和动态分区方法(This document details the basic elements of physical memory, and memory about the static and dynamic partition method of Division)
    2010-07-19 11:22:57下载
    积分:1
  • neural4
    neural programming with codes
    2014-11-20 11:38:37下载
    积分:1
  • emd
    EMD经验模态分解,用于信号处理,也常和hilbert变换一起用于信号特征提取、信号消噪等领域(EMD empirical mode decomposition for signal processing, and is often used in conjunction with hilbert transform signal feature extraction, signal de-noising and other fields)
    2015-03-17 10:03:18下载
    积分:1
  • chengxu
    小波变换进行变速箱故障诊断 首先将s1和s2信号时域谱(s1代表维修前的振动信号,s2代表维修后的振动信号),画出来进行对比,会发现s1信号的振动幅值会比较高;然后对s1和s2分别进行小波分解并画出各层的时域谱,只对比s1和s2分后的最高时域谱,s2更加的具有周期性,且幅值较小,s2周期性不够明显,且振动过于密集。分析完时域谱后开始分析频谱,首先对原信号s1和s2fft转换,得到频谱图,如图,然后再对小波分析后高频部分进行fft转换,做出频谱图。对比后我们发现,在f 2375HZ出(也就是齿轮的啮合频率),s1信号频谱幅值会有急剧的升高,然后,其谐波的幅值也会增大。所以可以推断出该维修前的增速箱的齿轮可能出现问题。(Gearbox fault diagnosis based on wavelet transform s1 and s2 first time domain signal spectrum (s1 behalf of the vibration signal before maintenance, vibration signal s2 representative of repaired), drawn comparison, you will find a signal s1 vibration amplitude will be higher then s1 and s2 respectively wavelet decomposition and draw the layers of time-domain spectrum to only a maximum time domain spectroscopy s1 and s2 points after, s2 is more cyclical and smaller magnitude, s2 cyclical enough obviously, and the vibration is too dense. End domain spectral analysis after the beginning of the spectrum analysis, the first of the original signal s1 and s2fft conversion to give the spectrum, as shown, and then after the high frequency part of wavelet analysis fft transformation to make spectrum. We found that after the comparison, at f 2375HZ out (i.e. the gear mesh frequency), there will be a sharp increase in the amplitude spectrum of the signal s1, and then, the amplitude of the ha)
    2017-01-17 19:18:02下载
    积分:1
  • ex4matlab05
    说明:  数学实验matlab的好程序,给matlab的初学者(Good mathematical experiment matlab program to matlab for beginners)
    2011-03-20 19:48:28下载
    积分:1
  • MIML-kNN
    It is a matlab code for K Nearest Neighbor algorithm.
    2013-04-01 22:54:40下载
    积分:1
  • helperCIFAR10Data
    创建一个CIFAR10DATA需要用到的一个matlab基础函数,可能系统版本中没有需要自行编写。(CREAT a CIFAR10DATA set,it may not excise in u matlab,need edit by youself.)
    2020-11-20 11:09:37下载
    积分:1
  • 696518资源总数
  • 104432会员总数
  • 16今日下载