-
多连接TCP
说明: 可实现TCP/IP连接后数据的读取与写入(TCP/IP data read and write)
- 2020-01-19 12:07:42下载
- 积分:1
-
labview
基于生产者与消费者的多通道数据采集与存储(Multichannel data acquisition and storage based on producer and consumer)
- 2017-08-16 14:43:32下载
- 积分:1
-
qiaodu
振动信号的峭度指标在labview中实现,对振动信号的评价很准。(Labview achieve signal kurtosis)
- 2021-04-01 12:39:08下载
- 积分:1
-
niScope EX Save to File
通过labview 2017以及pcix 5922数据采集卡完成数据采集,以及文本存储,还可以从文本中读取波形幅值。(Through lab view 2017 and pcix 5922 data acquisition card to complete data acquisition, as well as text storage, you can also read the waveform amplitude from the text.)
- 2020-11-05 19:19:50下载
- 积分:1
-
歪度指标VI
歪度指标是描述信号概率密度函数的重要参数。在对非平稳信号进行时域分析时,利用歪度指标反映了振动信号的非对称性,用来判断轴承是否发生碰磨。本文件中将歪度指标独立制作了子VI,便于labview程序调用。(The skewness index is an important parameter to describe the probability density function of a signal. When the non-stationary signals are analyzed in time domain, the skewness index is used to reflect the asymmetry of the vibration signals, which is used to judge whether the bearings have been touched or not. This document will be independent of the index made a sub VI, easy for LabVIEW program calls.)
- 2017-07-29 20:07:26下载
- 积分:1
-
RandomAverage
基于Labview环境编程的随机数求和界面显示,内容包含前台和后台等的建立(Based on the Labview environment programming of random number and interface display, the content includes the front and back and so on)
- 2015-07-31 18:35:11下载
- 积分:1
-
GPD-3303
固纬GPD-3303 labview串口通信驱动程序(this is labview driver for GGPD-3303.)
- 2020-11-23 10:19:34下载
- 积分:1
-
hanshuxinhaofashengqi
1.采用Labview设计一虚拟函数信号发生器, 通过数据采集卡输出波形信号,调节信号的相关参数,可观察示波器上波形的变化情况。
⑴ 以NI MyDAQ数据采集卡作为输出接口;
⑵ 数据采集卡输出多种信号,至少完成三种波形:正弦波、三角波、方波(可调占空比)的输出,同时前面板上显示各输出波形;
⑶ 频率、幅值、初相位、直流偏移量和方波的占空比(0~100 )等参数可以通过前面板控件调节。
⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes.
⑴ with NI MyDAQ data acquisition card as output interface
⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel
⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust.
⑷ output waveform can be displayed on the front panel.)
- 2015-04-25 18:26:52下载
- 积分:1
-
Serial Communication 14
利用labview操作者框架写的模拟串口通信,非常不错。(The analog serial communication written by the labview operator framework is very good.)
- 2020-06-17 03:00:02下载
- 积分:1
-
Bearing-frequency-calculate
所写的Labview程序可一次性计算出轴承的故障特征频率,方便实用(Written Labview program can calculate a one-time fault characteristic frequency of the bearing, convenient and practical)
- 2016-10-25 17:25:48下载
- 积分:1