登录
首页 » matlab » liti3_5

liti3_5

于 2014-10-20 发布 文件大小:1KB
0 97
下载积分: 1 下载次数: 11

代码说明:

  用矩阵撕裂法,多次用matlab运算,得出复杂系统的15个节点的电压(Tear voltage matrix method, repeatedly using matlab computing, complex systems derived 15 nodes)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Ch3figs
    《最优阵列处理》一书第三章的MATLAB例程,包括各种线性阵列和孔径的分析与合成算法。(" Optimal array processing," the third chapter of the book MATLAB routines, including linear arrays and aperture of the analysis and synthesis algorithms.)
    2009-04-13 00:22:57下载
    积分:1
  • usefull-skills-in-matlab
    matlab使用的N个实用技巧及其程序实现。(N-use practical skills and procedures matlab implementation.)
    2013-11-26 00:25:24下载
    积分:1
  • matlab--some-nice-programs
    Matlab画平滑曲线的两种方法( 拟合或插值后再用plot即可) 自然状态下,用plot画的是折线,而不是平滑曲线。有两种方法可以画平滑曲线,第一种是拟合的方法,第二种是用spcrv,其实原理应该都一样就是插值。下面是源程序。(You can then use the plot) Natural state, with the plot is a line drawing, instead of a smooth curve. There are two ways to draw a smooth curve, the first one is the fitting method, and the second is to use spcrv, in fact, the same principle should be that the interpolation. Here is the source.)
    2015-03-23 16:35:58下载
    积分:1
  • activeContoursSnakesDemo
    本演示实现了主动轮廓模型由Kass等人提出。 要运行它的图形用户界面 1。基于MATLAB型引导提示。 2。关于“到现有的图形用户界面,点击” 3。选择在与本文件相同的目录snk.fig文件 4。按一下上方的绿色箭头启动图形界面 一旦GUI已经启动,您可以通过使用蛇 1。点击“新形象”,并加载输入图像。提供的样品图像。 2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。 3。只要你点击“过滤器”,头发会出现交叉,用他们和你左击鼠标,您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下,你应该单击对象周围的一切你想要的部分。最后一点,必须挑选使用右键单击,以阻止更多的积分为MATLAB的要求。 4。设置各种蛇参数(在能源方面的相对权重的蛇目标函数)或离开它们的默认值,然后按一下他们“迭代”按钮。蛇会出现和移动,因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al. To run it with GUI 1. Type guide on the matlab prompt. 2. Click on "Go to Existing GUI" 3. Select the snk.fig file in the same directory as this file 4. Click the green arrow at the top to launch the GUI Once the GUI has been launched, you can use snakes by 1. Click on "New Image" and load an input image. Samples image are provided. 2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image. 3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points. 4. Set the various snake paramete)
    2010-07-05 11:54:13下载
    积分:1
  • chaos
    几个典型的混沌时间序列的生成程序,给出了各个混沌系统的吸引子图形(Several time series generated typical chaotic program)
    2010-06-01 10:12:27下载
    积分:1
  • dsp-2
    Impulse responses of systems
    2014-12-04 23:39:04下载
    积分:1
  • ART
    地震(超声)层析成像 利用ART反演算法计算走时 程序 (ART ART ART ART ART ART ART)
    2011-12-02 15:49:31下载
    积分:1
  • Work
    it is the best programe in matlab you can trait aplication whith the most faimous way bit we cant my you herlp me to do it rait
    2011-12-20 18:15:43下载
    积分:1
  • OFDMyuanshidaima
    本代码为OFDM的原始MATLAB仿真代码,已通过验证为 好代码(The original MATLAB code for OFDM simulation code has been validated as a good source)
    2009-11-24 13:29:42下载
    积分:1
  • prtools_ac
    模式识别工具箱,含有多类模式识别函数,是学习和写论文的好工具。(patern recognition toolbox, which contains vairous patern recognition functions)
    2010-06-02 17:01:40下载
    积分:1
  • 696518资源总数
  • 104432会员总数
  • 16今日下载