登录
首页 » matlab » ePic212

ePic212

于 2009-02-22 发布 文件大小:1570KB
0 101
下载积分: 1 下载次数: 39

代码说明:

  这是一个用来控制机器人ePuck的matlab GUI.通过它,使用者可以获取一切关于ePuck的感应器信息。(this is the matlab GUI program used on the robot ePuck.User can control the robot through it and also obtain the sensor reading.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • gaot
    遗传算法中最常用的通用工具箱 gaot(Genetic algorithms the most commonly used general-purpose toolbox gaot)
    2009-03-07 10:05:35下载
    积分:1
  • APSK
    General APSK system via matlab
    2011-09-15 09:09:40下载
    积分:1
  • A20130529112706
    matlab lagrange程序,适合大家编辑matlab 的拉格朗日程序文件,分析。(matlab lagrange program,it is suitable for programmer use lagrange original program to solve relative problem。)
    2013-10-18 09:23:27下载
    积分:1
  • dingshiguanji
    手把手教你如何用matlab调用系统程序,并自动控制电脑定时关机(Taught you how to use matlab call system procedures, and automatic computer shutdown timer)
    2010-06-05 19:30:01下载
    积分:1
  • KF_FineAlign
    这是一个很好的matlab精对准的详细程序(This is a matlab fine alignment program)
    2013-03-13 22:57:38下载
    积分:1
  • allpass5
    计算全通滤波器的源程序,根据信道群延迟,计算滤波器系数,用以校正信号相位变化(calculation of the all-pass filter source files, according to the channel group delay, filter coefficients calculated, for the correction signal phase changes)
    2021-05-09 16:38:34下载
    积分:1
  • Car-moving-by-Matlab
    本系统主要是设计一个简单的比例放大器,使小车能以指定的速度运动。采用“自下而上”,“分层”建模思想而设计的。主要包括了理论分析与设计、仿真系统的创建、仿真结果、仿真操作说明、结论等五部分。使用Matlab7.1实现(This system is mainly to design a simple proportional amplifier, so the car can be specified speed of movement. " Bottom up" and " layered" modeling idea. Include theoretical analysis and design, the creation of the simulation system, the simulation results, simulation instructions, conclusions of five parts.)
    2012-07-18 15:53:50下载
    积分:1
  • warping
    Here is some simple Matlab image warping code that I wrote a while ago that others continue to find useful. The code requires that you have Matlab and the Image Processing Toolkit installed
    2010-10-07 14:58:54下载
    积分:1
  • P_Controlv1.0
    说明:  用MATLAB实现的不合格品率P控制图的绘制,只要将数据导入data.txt文件,然后在MATLAB中运行main.m文件即可打开绘图界面。(注意:路径要设置好)(the failure rate of P Commodities Control Map, as long as the data into data.txt documents, then in MATLAB run main.m document can be open graphics interface. (Note : To set a good path))
    2006-04-16 12:07:55下载
    积分:1
  • pll_simulation
    本程序是一个PLL仿真程序,分为参数设置,仿真和后显示三部分.(this procedure is a PLL simulation program, is divided into parameters, simulation and revealed three parts.)
    2006-10-29 11:34:39下载
    积分:1
  • 696518资源总数
  • 104349会员总数
  • 32今日下载