登录
首页 » LabView » labview-capacity

labview-capacity

于 2013-08-03 发布 文件大小:45KB
0 119
下载积分: 1 下载次数: 6

代码说明:

  labview vi程序,基于版本8.2可以直接运行,,用来仿真电容充放电过程(labview vi program, based on version 8.2 can be run directly, to simulate capacitor charging and discharging process)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 偶数和
    说明:  FOR循环计算0——99偶数的和,用到for循环以及移位寄存器(FOR loop calculates the sum of 0-99 even numbers, using for loop and shift register)
    2020-06-18 23:20:01下载
    积分:1
  • numberofrandomgraphs
    随机数曲线例程,利用libview进行随机数曲线仿真计算(number of random graphs)
    2013-09-02 15:54:20下载
    积分:1
  • readexecl
    使用labview读取excel数据,绘制三维曲线和二维曲线(Using labview read excel data, drawing three-dimensional and two-dimensional curve curve)
    2013-07-30 15:51:53下载
    积分:1
  • oscilloscope
    利用DAQ助手实现的基于LABVIEW的示波器,可通过数据采集卡实现各种波形显示和尺度调节(Use the DAQ Assistant to achieve based on the LABVIEW the oscilloscope, data acquisition card to a variety of waveform display and adjust the scale)
    2012-08-15 16:02:09下载
    积分:1
  • fft
    labview 的傅里叶变换源程序 对输入信号做傅里叶变换后,将输入信号从时域变换的频域中,从而在频域中对输入信号的各种特征进行分析,比如做滤波处理,调制信号等。(the Fourier Transformation Code Based On Labview )
    2016-04-14 09:44:40下载
    积分:1
  • Laser-sensor-program
    主要实现激光传感器与上位机的实时通信功能。(The main function of laser sensors for real-time communication with the host computer.)
    2015-10-31 15:57:32下载
    积分:1
  • USART
    基于单片机设计的LabVIW的串口通讯实例(Serial communication instance-based single-chip design LabVIW)
    2012-06-18 15:19:40下载
    积分:1
  • AFG3000s-Sweep-Frequency
    利用LabView 程序控制 数字信号源AFG3000进行频率扫描(LabVIEW program control digital signal source AFG3000 frequency sweep)
    2020-09-10 17:08:00下载
    积分:1
  • 基于LabVIEW的通用自动测试系统设计
    说明:  基于LabvIEw的通用自动测试系统(ATs)舍计算机,可鳊程激励、响应数据采集及uuT模块,采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号,矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序,信号发生器发送激励信号,数据采集卡采集数据,采集数据经调理后,并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)
    2020-10-24 12:27:23下载
    积分:1
  • 数据采集指南 上篇
    Introduction of NI data acquisition hardware 1. Basic components of a complete data acquisition system 2. NI provides data acquisition hardware products based on which platforms and which application areas they are suitable for respectively. 3. What important parameters should be paid attention to in the process of hardware selection of data acquisition equipment
    2020-06-21 20:00:02下载
    积分:1
  • 696518资源总数
  • 104388会员总数
  • 18今日下载