-
??2??￡?μ?èˉ?
说明： labview modbus协议下的串口通信(Serial communication under LabVIEW Modbus Protocol)
- 2020-06-21 13:00:01下载
- 积分：1
-
labviewscreenshot
labview的截图软件 非常好用可以实现桌面截图(LabVIEW screenshot of the software is very good to use the desktop screenshot)
- 2015-08-28 09:37:58下载
- 积分：1
-
Labview3Dcontrols_examples
Labview的3D控件的功能介绍，还有三个例子程序：陀螺仪，2D魔方，3D魔方。(Function Labview 3D controls introduction, there are three examples: gyroscope, 2D Rubik' s Cube, 3D cube.)
- 2014-01-26 09:41:19下载
- 积分：1
-
1-myRIO-8.30
利用MyRio，发出指定脉冲数，来控制电机(Using MyRio, the number of the specified pulse is issued to control the motor.)
- 2021-05-14 03:30:02下载
- 积分：1
-
kuaipai
说明： 利用 labview面向对象编写的快速排序算法，技能学习算法，又能学习基础知识(Use labview object-oriented fast sorting algorithm, skill learning algorithm, and learn basic knowledge)
- 2020-06-17 02:40:01下载
- 积分：1
-
daq
本文主要介绍了利用国产普通数据采集卡，基于美国 NI 公司提供的虚拟仪
器软件开发平台 LabVIEW 和实验室原有发动机硬件平台自行开发的一套气缸压
力采集模块和数据分析模块(This thesis primarily introduced software about cylinder pressure and crank
angle acquisition and data analysis module. It is designed by using a general data
acquisition board, which is based on Virtual Instrument LabVIEW offered by NI and
laboratory engine.
)
- 2013-05-23 20:34:34下载
- 积分：1
-
asd
航空航天通信技术一般采用模拟通信的频率调制和数字通信的移相键控调制方法。这有利于充分应用信道带宽和能源。频率调制是在一定程度上改变载波或副载波的频率来传输信息的调制方法。移相键控调制是利用载波或副载波的相位跳变来传输信息的调制方法。移相键控又分二相移相键控、四相移相键控和多相移相键控，其中以四相移相键控和八相移相键控调制方法的效率较高(Aerospace communications technology commonly used analog communication of frequency modulation and the digital communication phase shift keying modulation method. This is helpful for making full use of channel bandwidth and energy. Frequency modulation is changed to some extent carrier or subcarrier frequency to transmit information modulation method. Phase shift keying modulation is the use of carrier or subcarrier phase jump to transmit information modulation method. Phase shift keying and binary phase shift keying, four phase shift keying and multiple phase shift keying, of which four phase shift keying and eight phase shift keying modulation method of high efficiency
)
- 2011-07-13 11:21:08下载
- 积分：1
-
Untitled-2
实现多通道的应变采集，包括自动清0，手动清0等(Multi-channel strain collection, including cleared automatically, manually cleared, etc.)
- 2011-07-14 14:46:54下载
- 积分：1
-
基于LabVIEW的通用自动测试系统设计
说明： 基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)
- 2020-10-24 12:27:23下载
- 积分：1
-
振动信号采集分析程序
说明： 对振动信号采集和分析，包括信号采集，时域分析，品与分析 故障定位(Vibration signal acquisition and analysis)
- 2020-11-07 10:09:49下载
- 积分：1
