-
峭度指标VI
峭度指标是非平稳信号故障诊断的重要参数。峭度指标对信号中的冲击成分十分敏感，冲击成分能量越大，其峭度值就会越大，在故障诊断的时域分析中十分重要。本文件中将其独立做成了一个子vi，便于程序直接调用。(Kurtosis index is an important parameter of non-stationary signal fault diagnosis. The kurtosis index is very sensitive to the impact component in the signal. The greater the energy of the shock component, the greater the kurtosis of the signal, and it is very important in the time domain analysis of the fault diagnosis. This document will be independent of a sub VI, to facilitate direct calls to the program.)
- 2017-07-29 20:12:45下载
- 积分：1
-
CVI打开文件程序 fileopen
CVI打开文件程序，使用labwindows 2010 编写(cvi open file)
- 2014-08-07 12:33:51下载
- 积分：1
-
Frequency-Hopping-test
参考如何修改载波频率实现跳频，参考如何获取USRP时钟信息(How to modify the carrier frequency hopping to achieve, how to get USRP clock reference information)
- 2016-03-30 15:19:56下载
- 积分：1
-
esp1
汽车稳定性控制ESP的LabVIEW程序，经过实际验证，精度较好。(Vehicle Stability Control ESP LabVIEW program, after the actual verification, the accuracy is better.)
- 2014-06-08 22:07:52下载
- 积分：1
-
Kamera_FGV
关于图像采集和处理的实际例子，适合新手学习学习(grab image and processing)
- 2019-03-05 14:17:10下载
- 积分：1
-
readCSVandwrite
说明： 通过读取本地CSV文件，筛选里面数据后，传输至指定数据库(By reading the local CSV data, it is transmitted to the database.)
- 2019-04-02 22:43:52下载
- 积分：1
-
hanshuxinhaofashengqi
1．采用Labview设计一虚拟函数信号发生器， 通过数据采集卡输出波形信号，调节信号的相关参数，可观察示波器上波形的变化情况。
⑴ 以NI MyDAQ数据采集卡作为输出接口；
⑵ 数据采集卡输出多种信号，至少完成三种波形：正弦波、三角波、方波(可调占空比)的输出，同时前面板上显示各输出波形；
⑶ 频率、幅值、初相位、直流偏移量和方波的占空比（0～100 ）等参数可以通过前面板控件调节。
⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes.
⑴ with NI MyDAQ data acquisition card as output interface
⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel
⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust.
⑷ output waveform can be displayed on the front panel.)
- 2015-04-25 18:26:52下载
- 积分：1
-
停车场系统
用LabVIEW模拟停车场系统,实现分段计时收费(LabVIEW simulation of parking system, to achieve sub hourly fees)
- 2020-11-06 22:09:50下载
- 积分：1
-
labview-and-Delphi
labview和delphi是教程中的关盘中的内容，完了会传更多，把这里面的例子作为学习资料还是很好的，这可以做智能车的上位机，绝对原版资料(labview delphi tutorial off disc, as examples of these learning materials inside is very good, it can do the smart car PC, absolutely original information)
- 2013-06-09 12:47:14下载
- 积分：1
-
kvCanVi
实现Kvaser的CAN通讯，能实现简单的读写CAN信号。(The CAN communication of Kvaser can be realized, and CAN signal can be read and written simply.)
- 2020-12-17 22:59:11下载
- 积分：1
