-
Neural-network
实现基于单片机的神经网络算法，C语言编写，供参考。(Neural network on the realization of singlechip)
- 2012-09-22 15:36:29下载
- 积分：1
-
STC-chip-programmer
STC芯片烧写软件,专用于STC芯片的单片机程序烧录(STC chip programmer software)
- 2013-08-11 14:19:47下载
- 积分：1
-
Vibration-and-sound-
P.M.莫尔斯的《振动与声》经典之作。各种宏观的声学问题。(PM Morse, " Vibration and sound classic. A variety of macro-acoustic problems.)
- 2012-06-07 20:35:09下载
- 积分：1
-
WaveSave
一个简单的串口示波器，使用的时候请首先安装labview 的visa驱动 此文件为labview2014创建，请使用不低于labview2014的版本打开使用。(a simple OSC using serial port)
- 2015-12-30 08:41:13下载
- 积分：1
-
IIC-OLED
说明： stm32f429 iic oled mdk环境(Stm32f429 IIC OLED MDK environment)
- 2020-06-16 02:40:02下载
- 积分：1
-
Automatic-traffic-control-system-
自动交通控制系统用红、绿、黄三支共两组发光二极管表示交通信号灯，利用单片机模拟有时间显示的定时交通信号灯控制管理。信号灯的变化规律可如下：
1）放行线：绿灯亮放行25秒，黄灯亮警告5秒，然后红灯亮禁止。
2）禁示线：红灯亮禁止30秒，然后绿灯亮放行。
3）当某一方向的红灯亮时，若该方向有车通过，则用扬声器声报警。（撞红灯信号可用3-5V模拟量表示）(Automatic traffic control system using red, green, yellow light-emitting diodes, said a total of three traffic lights, the use of single-chip analog time display on a regular traffic signal control and management. Changes of lights to be as follows: 1) Release Line: green clearance 25 seconds, the yellow light warning for 5 seconds, then the red light is prohibited. 2) ban shows lines: the red light is prohibited for 30 seconds, then the green light to release. 3) When the red light in one direction, if the direction of the car through, the alarm speaker sound. (Hit the red signal available 3-5V analog representation))
- 2013-12-19 18:26:11下载
- 积分：1
-
1
51单片机控制 套丝机机床实现自动加工螺纹钢(motor cw ccw)
- 2013-11-15 00:07:21下载
- 积分：1
-
实验5_硬件乘法器操作
说明： ＭＳＰ４３０Ｆ４４９的硬件乘法器操作IAR Practice code(MSP430F449 hardware multiplier operation code IAR Practice)
- 2005-09-08 13:39:08下载
- 积分：1
-
STC15W单片机的MAX7219显示测试
说明： 基于STC15W系列单片机，实现一种常用的MAX7219驱动的8位数码管显示模块的程序。(Based on STC15W series MCU, a program of 8-bit digital tube display module driven by MAX7219 is implemented.)
- 2020-06-20 23:00:01下载
- 积分：1
-
步进电机
编制MCS-51程序使步进电机按照规定的转速和方向进行旋转，并将已转动的步数显示在数码管上。
步进电机的转速分为两档，当按下S1开关时，加速旋转，速度从10转/分加速到60转/分。当松开开关时，减速旋转，速度恢复为10转/分。当按下S2开关时，按照逆时针旋转；当松开时，按照顺时针旋转。
本程序要求使用定时器中断来实现，不准使用程序延时的方式。(The MCS-51 program is programmed to rotate the stepper motor according to the specified speed and direction, and the number of steps that have been rotated is displayed on the digital tube.
Stepper motor speed is divided into two gears. When the S1 switch is pressed, the speed is accelerated from 10 rpm to 60 rpm. When the switch is loosened, the speed will be reduced to 10 rpm. When pressing the S2 switch, rotate counterclockwise; when loosening, rotate clockwise.
This procedure requires the use of timer interrupt to achieve, do not use the way of program delay.)
- 2020-06-16 09:40:02下载
- 积分：1
