登录
首页 » matlab » pid

pid

于 2009-02-04 发布 文件大小:4KB
0 106
下载积分: 1 下载次数: 213

代码说明:

  单纯形法整定pid参数,simulink环境,单纯形法很依赖初值的选取,在canshu.m中输入初始值。(Simplex method pid tuning parameters, simulink environment, simplex method is very dependent on the selection of initial value, in canshu.m enter the initial value.)

文件列表:

pid参数整定
...........\canshu.m
...........\optm.m
...........\pid.mdl

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • sp.m
    基于扩频的数字水印技术,水印信息分布于载体作品的多个频率系数,每个频率系数上负荷的水印能量很小,平衡水印的鲁棒性和不可感知性上的矛盾。(Digital watermarking based on spread spectrum technology, the watermark is found in a number of frequency coefficient vector works, each frequency coefficient on the load of the watermark energy is small, balance the robustness and non-perception of the conflict.)
    2010-06-03 10:27:03下载
    积分:1
  • Truss-Analysis
    In this finite element application is descriptioned simple space a struss system analysis with only linear static model. This analysis model is very simplest. Fistly, selecting system model is solution analytical, secondly analysis Matlab and analysis results was compared the S.A.P2000 (structural analysis program). All analytical models, Matlab analysis are satify as analysis Results.
    2013-01-18 15:42:14下载
    积分:1
  • extremaa
    to find the extremas of any 1-d signal
    2011-09-17 21:54:01下载
    积分:1
  • sliding mode
    说明:  主要讨论了几种不同的滑模控制算法,可用于轨迹跟踪。(Several different sliding mode control algorithms are discussed, which can be used for trajectory tracking)
    2021-04-08 13:19:01下载
    积分:1
  • IMMPDA
    里面有程序,还有pdf文献.都是有关目标跟踪的.程序是多模型算法(There are procedures, as well as pdf documents. Are related to target tracking. Program is a multi-model algorithm )
    2020-11-24 18:09:41下载
    积分:1
  • Digital_Watermarking_and_Steganog
    digital image processing book
    2013-01-09 15:58:29下载
    积分:1
  • MATLAB
    MATLAB N个实用技巧--MATLAB中文论坛精华总结(it is useful for new learner )
    2014-09-10 16:00:52下载
    积分:1
  • attachments
    This file contains optimization codes
    2013-08-01 00:55:29下载
    积分:1
  • integer-programming
    三种整数规划的matlab程序,很实用,百分之百保证好用,都经过实测的(Three kinds of integer programming matlab program, it is practical, easy to use 100 guaranteed, have been measured)
    2011-11-29 19:53:36下载
    积分:1
  • amplitude
    本源代码用来求解机床振动(时间-加速度)信号采集过后的数据,求出其平均幅值,并绘图(This source code is used to solve machine tool vibration (time)- acceleration signal after the acquisition of data, find out the average amplitude, and drawing )
    2016-03-25 15:37:57下载
    积分:1
  • 696518资源总数
  • 104349会员总数
  • 32今日下载