-
Generalizedpredictivecontrolcode
广义预测控制的实现及程序代码和程序源代码的说明(Generalized predictive control code)
- 2009-03-03 11:17:54下载
- 积分：1
-
103244852ofdmmatlab
OFDM限幅类峰均比,用于仿真OFDM系统中的限幅类峰均比。(Limiter type OFDM PAPR for OFDM simulation system PAPR limiting category.)
- 2008-05-26 16:33:36下载
- 积分：1
-
matlab_time-frequencytoolbox
matlab非常有用的工具箱，可对非平稳信号进行分析与处理。(matlab toolbox very useful, may be non-stationary signal analysis and processing.)
- 2007-11-28 10:04:33下载
- 积分：1
-
license
用于求解matlab排序问题，求解得效率很高，比一般的方法好哦(Matlab for solving the scheduling problem, to solve a highly efficient method than the average好哦)
- 2009-04-10 17:55:46下载
- 积分：1
-
setLevel-Img
embedding file image into audio file in this case wave file
- 2011-08-31 03:09:57下载
- 积分：1
-
SVD-EOF
基于matlab,采用SVD方法，对数据进行EOF分解，求得基函数(Based on matlab, using SVD method, the data EOF decomposition, obtained basis functions)
- 2014-02-25 10:47:12下载
- 积分：1
-
dijkstra
求解图中起点到任意一个点的最小距离 输出len 和 meth分别记录长度 和 父亲点(Solving the graph point of origin to any point of a minimum distance of the output record length len, and meth and father respectively, point)
- 2010-02-07 11:29:59下载
- 积分：1
-
OFDM111
pca、kpca.dpca的故障诊断程序，有很好的效果，对象为csth和cstr，希望对你有用(Pca, kpca. Dpca fault diagnosis procedure, have very good effect, the object for CSTH and CSTR, hope to be useful to you)
- 2011-12-25 22:33:40下载
- 积分：1
-
基于有限差分法的二维边值问题的数值分析
1. 在matlab中分析基于分离变量法的解析解；
2. 利用简单迭代法求解，与解析法结论对比，分析求解结果的精确度。分析过程至少包括：在网格尺寸为0.1 m和1 m两种条件下，两次迭代差值最大为10-10时的分析结论；
3. 利用超松弛迭代法分析，选择松弛因子，分析其对收敛速度（即迭代次数）的影响，并确定最优值。分析过程至少包括：在网格尺寸为0.1和1两种条件下，两次迭代差值最大为10-10时，迭代次数随松弛因子的变化，得到对应的最优松弛因子，与经验值（课本165页式子3.7.15）进行对比。(1. Analyze the analytical solution based on the separation variable method in matlab.
2. Using a simple iterative method to solve, compared with the results of the analytical method to analyze the accuracy of the solution. The analysis process at least includes the following conclusions: when the mesh size is 0.1m and 1m, the maximum difference between two iterations is 10-10.
3. Analyze using the relaxation relaxation iteration method, select the relaxation factor, analyze its influence on the convergence speed (ie the number of iterations), and determine the optimal value. The analysis process at least includes the following: when the mesh size is 0.1 and 1 and the maximum difference between two iterations is 10-10, the number of iterations varies with the relaxation factor, and the corresponding optimal relaxation factor and empirical value are obtained ( Textbook 165 pages (3.7.15) for comparison.)
- 2020-07-28 18:48:39下载
- 积分：1
-
superGMSK_matlab
GMSK调制 实现了毕业设计要求的GMSK的基本功能 其中包括simulink建模(GMSK modulation to achieve the design requirements of the graduation of the basic functions of GMSK including simulink modeling)
- 2008-05-27 01:19:12下载
- 积分：1
