-
yasuoronghe
图形压缩，融合是图形处理的必需步骤。利用matlab仿真，简单(Graphics compression, integration is an essential step in graphics processing. Matlab simulation using simple)
- 2009-05-14 11:15:19下载
- 积分：1
-
newton-chazhi
Newton插值公式实例，改变插值节点个数，观察不同的插值函数的逼近效果.(Instance of the Newton interpolation formula, change the number of interpolation nodes, and observe the different interpolation function approximation.)
- 2012-04-13 15:51:43下载
- 积分：1
-
model3
蓄电池容量检测模型，本人毕业论文成果，matlab6.5(Battery capacity test model, I thesis results, matlab6.5)
- 2011-06-30 11:40:49下载
- 积分：1
-
main_AWGN
高斯白噪声信道的误码率性能的matlab的m文件(BER performance over AWGN channel)
- 2010-08-25 21:25:08下载
- 积分：1
-
ANNPID
分别采用4种控制律进行单神经元PID控制,即无监督的Hebb学习规则、有监督的Delta学习规则、有监督的Hebb学习规则、改进的Hebb学习规则.(Separately using four kinds of control laws for single neuron PID control, that is, unsupervised Hebb learning rules, there is the Delta Study supervision rules, there is supervised Hebb learning rule to improve the Hebb learning rule.)
- 2009-03-24 18:23:38下载
- 积分：1
-
complex
This disk contains numerical methods software coded in MATLAB. The algorithms are described in the text NUMERICAL METHODS for Mathematics, Science, and Engineering.FORTRAN
- 2010-11-03 02:07:00下载
- 积分：1
-
LFM
说明： LFM波形产生，匹配滤波输出，匹配滤波器输出(LFM waveform generator, matched filter output, matched filter output)
- 2011-03-22 16:39:38下载
- 积分：1
-
niudun_qianxiangchazhi
数值分析——利用牛顿前向插值方法计算atanx的Newton形式的系数(Numerical analysis- interpolation using Newton' s method to calculate atanx before the Newton form factor)
- 2011-07-07 19:22:15下载
- 积分：1
-
PID
一个比较典型的PID处理程序，在使用单片机作为控制cpu时，请稍作简化，具体的PID
参数必须由具体对象通过实验确定。由于单片机的处理速度和ram资源的限制，一般不采用浮点数运算，
而将所有参数全部用整数，运算到最后再除以一个2的N次方数据（相当于移位），作类似定点数运算，可
大大提高运算速度，根据控制精度的不同要求，当精度要求很高时，注意保留移位引起的“余数”，做好余
数补偿。这个程序只是一般常用pid算法的基本架构，没有包含输入输出处理部分。
(A typical PID process, using the microcontroller as a control cpu, make some simplification, the specific PID parameters must be determined experimentally by a specific object. As the chip processing speed and ram resource constraints, generally do not use floating-point operations, and all parameters of all integers, and divided by an operator to the last N-th power of 2 data (the equivalent of the shift) for a similar fixed-point operations, can greatly improve the speed of operation, according to the different requirements of precision control, when high precision, attention to retain the shift caused by the " remainder" and on the remainder of compensation. This procedure is commonly used basic structure pid algorithm, does not include input and output processing section.)
- 2011-07-17 23:45:45下载
- 积分：1
-
PCMA
单通道PCMA信号的盲分离算法，包括主程序中BPSK信号源的产生源码及单路信号正交分解(Single-channel blind signal separation algorithm PCMA, including the main source of BPSK signals in the generation of single signal source and the orthogonal decomposition)
- 2021-03-02 13:09:34下载
- 积分：1
