-
HigherOrderGaussianPulseForUWB
These matlab codes are for UWB and Higher order Gaussian pulses.
- 2010-10-05 12:15:14下载
- 积分：1
-
Python-GUI-Programming-using-Tcl[1]
its book to gui development for python
- 2014-11-13 11:49:42下载
- 积分：1
-
walker
使用matlab写了一个很有意思的程序 大家看看作为参考(Use matlab write a very interesting program we look at as a reference)
- 2012-09-08 21:23:09下载
- 积分：1
-
findiff
Cholesky分解，以某个具体的矩阵进行的分解，便于求解线性方程组(Cholesky decomposition)
- 2012-05-13 17:32:49下载
- 积分：1
-
gui
说明： gui用户界面，傻瓜式读取任意oisst的nc文件，并绘制sst全球分布图(GUI user interface, reading NC files of any oisst and drawing global distribution map of SST)
- 2020-06-10 10:28:43下载
- 积分：1
-
TSPSAA
模拟退火算法在MATLAB环境下解决旅行商问题，实例代码(Simulated annealing algorithm in MATLAB environment to solve the traveling salesman problem, example code)
- 2013-03-18 16:23:52下载
- 积分：1
-
IT
说明： 详细介绍了一种新的仿真软件IT++ 比matlab有更快的执行效率 (Introduced a new simulation software IT++ faster than the efficiency with matlab)
- 2010-05-31 10:05:41下载
- 积分：1
-
strech
去斜率（strech）参考信号与回波信号混频后得到中频输出信号S(t)=Aexp(j*2*pi*f0*t+phase)
其中f0与回波延时的关系为：
f0=k*delay_t
K为线性调频斜率，delay_t为回波延时
将s(t)采样，FFT变换即可得到目标距离与频谱的关系。
Strech 信号测距
输入混频后的中频信号（图一），经采样及FFT变换得到频谱（图二）
再根据频谱与距离的关系式R=Tcf/2B显示出距离(图三)
(Go slope (strech) obtained after the reference signal and the echo signal mixer IF output signal S (t) = Aexp (j* 2* pi* f0* t+phase) f0 and echo delay relationship: f0 = k* delay_t K chirp slope, delay_t the echo delay sampling s (t), the FFT transform to the target distance spectrum of relations. Strech signal ranging input mixer IF signal (Figure 1), sampling and FFT transform spectrum (Figure 2) according the the spectrum distance relationship R = Tcf/2B shows the distance (Figure 3))
- 2012-11-27 20:36:34下载
- 积分：1
-
小孔节流静压气浮轴承的压力模拟 Orifice-hydrostatic-air-bearing
小孔节流静压气浮轴承的压力模拟，使用差分法计算(Orifice hydrostatic pressure simulation of air bearing, calculated using the difference method)
- 2020-06-27 07:40:01下载
- 积分：1
-
06mce001
This project describes identification of number plate from vedio.
- 2009-02-19 17:37:08下载
- 积分：1
