登录
首页 » matlab » PCA

PCA

于 2012-03-24 发布 文件大小:12KB
0 87
下载积分: 1 下载次数: 5

代码说明:

  Principal component analysis .m file

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • matlab
    Computing with Mathematica, 2nd edition.pdf
    2010-12-14 04:41:35下载
    积分:1
  • Sun
    简单的图像展开,使用与要求不高的场合,MATLAB(Simple image expansion, use and less demanding situations, MATLAB)
    2014-12-15 10:56:00下载
    积分:1
  • exer_Baton5
    stirling engine simulation with matlab
    2013-12-07 23:57:44下载
    积分:1
  • pulseDsP
    这是脉象信号的处理数据,可以得出最佳取脉压力,是很好的处理程序(This is the pulse signal processing data, we can draw the best to take the pulse pressure is a good handler)
    2013-12-19 21:20:27下载
    积分:1
  • CS_MRI_Contourlet
    这是CS-mRI代码,主要应用于医学磁共振图片的压缩感知处理代码(This is the CS-mRI code, mainly used in medical magnetic resonance image compression perceptual processing code)
    2013-03-15 10:36:47下载
    积分:1
  • pv
    说明:  A SIMPLE MODELING OF PHOTOVOLTAIC CELLE IN MATLAB SIMULINK
    2014-11-06 04:09:38下载
    积分:1
  • ofdm_gito
    Coded OFDM system over multipath channel
    2009-10-29 01:13:12下载
    积分:1
  • add-noise
    添加随机白噪音方法,用于时序仿真分析,仅供参考!(Add noise for simulation)
    2013-10-16 14:59:52下载
    积分:1
  • TransientStabilityOLD
    This program running in Matlab related to power system transient.
    2012-09-15 15:15:44下载
    积分:1
  • OFDM rece matlab
    接收端采用的算法和程序流程与发送端发送的OFDM符号的帧结构有关系。具体的帧结构,以及定时估计,频偏估计,剩余误差跟踪的算法可参考算法说明文档。这里对程序的流程进行说明。 首先根据短训练字的特性进行相关运算,进行信号到达检测,当检测到相关值大于门限一定次数后,认为有信号到达。然后根据长训练字的特性,进行相关运算,进行OFDM符号FFT窗口起始位置的估计。估计出FFT窗口的位置后,先在时域进行小频偏的估计,将两个长训练字进行小频偏补偿后,进行FFT运算,根据FFT运算的结果进行整数倍频偏的估计。这些参数估计完成后,就可以进行数据解调了。先对数据部分进行完整的频偏补偿,然后根据估计的FFT窗口位置进行FFT运算得到频域的数据,进行解调。然后在对应于导频的子载波位置上提取出导频信息,根据导频信息估计出剩余定时误差以及剩余的信道响应误差,将误差量送入环路进行跟踪。当收到所有数据后,重新回到信号到达检测状态,进行下一次信号到达的检测和信号接收。 (The receiving end uses the algorithm and the program flow and the frame structure of the OFDM symbol transmitted by the sending end. Specific frame structure, and timing estimation, frequency offset estimation, residual error tracking algorithm can refer to the documentation. Here to illustrate the process of the program. First, according to the characteristics of the short training word correlation operation, the signal reaches the detection, when the correlation value is greater than the threshold of a certain number of times, that there is a signal to reach. Then, according to the characteristics of the long training word, the correlation operation is carried out, and the initial position of the OFDM symbol FFT is estimated. The estimated position of the FFT window, first in the time domain for small frequency offset estimation, two long training word for small frequency offset compensation, the FFT operation. According to the result of FFT for integer frequency bias estimation. Af)
    2020-11-05 00:19:52下载
    积分:1
  • 696518资源总数
  • 104269会员总数
  • 42今日下载