▍1. Arduino-Bluetooth-control-a-car
基于Arduino的蓝牙控制小车,利用手机蓝牙,控制电机的正反转等功能。(Based on the Arduino bluetooth control the car, mobile phone bluetooth, control motor and reversing, and other functions.)
基于Arduino的蓝牙控制小车,利用手机蓝牙,控制电机的正反转等功能。(Based on the Arduino bluetooth control the car, mobile phone bluetooth, control motor and reversing, and other functions.)
这是一个利用dsp2812开发版自带的ad转化器,实现电信号转化成数字信号,并将数据存贮在存贮器的程序(This is a using DSP2812 development version comes with AD converter, realizes the electrical signal into digital signal and the data stored in the memory of the program )
这是一个利用dsp的gpio口实现不同的功能模块和数字口功能,程序完整可运行(This is a use of the GPIO DSP port to achieve different functions and functions of the function module, the program can run )
模糊控制结合PID控制算法的实现。已在DSP处理器上实现对电机的控制。(Fuzzy control combined with PID control algorithm implementation. The motor control has been achieved on the DSP processor.)
自己写的TMS320F28335代码,内含DA、AD、液晶驱动、峰值检测、频率采集等程序,供参考(TMS320F28335 write their own code, containing DA, AD, LCD driver, peak detection, frequency acquisition procedures for reference)
语音信号的FIR滤波工程,可在DSP 5509A环境下运行,并运用CCS图形工具观测滤波效果。(FIR filtering of speech signal, can be run in the 5509A DSP environment, and the use of CCS graphics tools to observe the filtering effect.)
本教程使用的DSP库来自ARM官方,此库支持以CM0,CM3,CM4以及CM7为内核的所有MCU。本期教程主要讲解支持函数中的Q7,Q15和Q31分别向其它类型数据转换。(This tutorial uses a DSP library the ARM official, this library supports CM0, CM3, CM4 and CM7 for the kernel of all MCU. )
微网的双模式研究,对微电网逆变器的下垂控制、PQ控制以及孤岛检测方法进行了调研,对它们进行简要的叙述,文档作为课题的开题报告(Dual-mode research for microgrid)
研旭TMS320F28335 DSP开发板EEPROM示例程序,如果使用CCS3.3拷贝到安装目录下的MyProject下,不能有中文路径(YanxuTMS320F28335 DSP research development board EEPROM sample program.In CCS3.3 please copy this to MyProject installation directory. Chinese path is invalid.)
本教程使用的DSP库来自ARM官方,此库支持以CM0,CM3,CM4以及CM7为内核的所有MCU。本期教程开始带领大家学习DSP教程,学习前首相要搞明白一个概念,DSP有两层含义,一个是DSP芯片也就是Digital Signal Processor,另一个是Digital Signal Processing,也就是我们常说的数字信号处理技术。本教程主要讲的是后者。( This tutorial uses a DSP library the ARM official, this library supports CM0, CM3, CM4 and CM7 for the kernel of all MCU.)
keystone架构TMS320C6678芯片的基本外设驱动。包括串口、SPI、GPIO等。也可用于其他6000系列的DSP芯片(the basic software of TMS320C6678,including the UART,SPI and GPIO. This software can be applied to other C6000 Digital signal Processing chip.)
在ADI公司dsp芯片sharc21489中通过DMA实现延时功能,配合sigma for sharc使用,输入有两个参数,一个是延时时间,另一个是延时需要放在片外那个地址。(In sharc21489 delay by the DMA function, with sigma for sharc use, there are two input parameters, a delay time, and the other is the delay needs to be placed chip that address)
本人基于ti dsp 开发环境CCS的四旋翼程序(I am four rotor based on ti DSP development environment CCS)
说明: 针对TI DSP C6000系列的局域网监控开发,在CCS开发环境运行。能实现局域网数据包抓包、数据包分析,特定数据包内容读取,异常数据包报警等功能。运行CCS注意配置好安装调用路径(For LAN monitoring the development of TI DSP C6000 series in CCS development environment running. Enables LAN data packet capture, packet analysis, specific packet content to read, malformed packets alarm. Run CCS note configured installation call path)
使用TMS320F28335开发的异步电机控制程序,程序注释很详细,适合异步电机控制的开发人员参考(TMS320F28335 developed using asynchronous motor control program, the program is very detailed comments, developer for induction motor control reference)