▍1. Maindfdsffdsaf
一个无线收发程序,使用megal8进行无线收发,定义了无线收发的协议(a wireless transceiver, the use of megal8 for wireless transceiver, a wireless transceiver defined in the agreement)
一个无线收发程序,使用megal8进行无线收发,定义了无线收发的协议(a wireless transceiver, the use of megal8 for wireless transceiver, a wireless transceiver defined in the agreement)
好东西 top编程器使用说明top编程器使用说明top编程器精美包装top编程器安装光盘top2005编程器精致外观ep51编程器,51单片机学习网(深圳学林电子有限公司)隆重推出!方便精巧,可靠性高, 烧写速度快,是初学单片机的入门利器!全面兼容.. (good things top programmer for use top programmer for use top programmer beautifully packaged top Programming installation CD top2005 programmer refined appearance ep51 programmer, 51 SCM learning network (Shenzhen Xuelin Electronics Co., Ltd.) launched a grand! facilitate sophisticated, high reliability, burning speed, is a novice SCM induction weapon! fully compatible ..)
这是用asm编写的IOA口使用程序,是用16位的凌阳单片机汇编(This is asm2 prepared by the IOA I use the program is the use of Sunplus 16 MCU Series)
ATT7026汇编语言读写程序,原理图,可以直接做成三相电表。(ATT7026 assembly language literacy procedures, drawings, and can directly create three-phase transformer.)
c8051f020单片机控制铁电存储器FM24CL04的驱动程序,环境keil,汇编编写(C8051f020 SCM control FM24CL04 ferroelectric memory of the driver, c51 environment, compilation preparation)
编写一个中断处理程序,在主程序运行过程中,每隔10秒响铃一次,同时在屏幕右上角开窗口显示信息“The bell is ring!” 以及时、分、秒。(prepared an interrupt handling procedures, the main program process, beep every 10 seconds once, in the upper right open window screen display information, "The bell is ring!" And, minutes and seconds.)
介绍了用74HC595驱动LED显示的程序,用汇编编的(introduces the Bit LED Display Driver procedures used in the compilation series)
C51驱动LCD显示器的单片机程序。可以显示英文,数字(C51-driven LCD monitor SCM procedures. It shows in English, figures)
说明: 软件模拟解码PT2262(晶体:12MHZ)(simulation software decoder PT2262 (Crystal : 12MHZ))
说明: 工业仪器仪表类: 内容为测量仪器,传感器采集数据,通信等(industrial instrumentation categories : content of measuring instruments, sensor data collection, communications, etc.)
说明: 超声波测距基于8051的源程序设计(8051 Ultrasonic Ranging based on the source code design)
说明: 一个测试凌阳61板中FLASH的程序,用汇报和C混合编写的(a test Sunplus 61 plate FLASH the procedures used to report and the preparation of the hybrid C)
说明: modbus通信规约的汇编程序,可供通信编程时参考使用(Modbus communication protocol compilation procedures, communications programming for the use of reference)
说明: 该抢答器供不多于4个参赛队或者个人的抢答比赛场合使用。每个参赛队的座位前 安装1只抢答按钮开关(用板上的S9、S10、S11、S12)和一个信号灯(D4、D5、D6、D7)。 主持人座位前装一只复原开关(板上S3)、1只蜂鸣器(板上BUZ1)和一个抢答器工作状态 指示灯(D10),每当主持人口头发出号令之后.哪个队先按下座位上的按钮开关,该座位的信 号灯就先被点亮,同时封锁其他按钮开关的活动.并且熄灭主持人座位上的状态指示灯和发出 三声类似于电话振铃的提示声,以声明此次抢答动作已经完成.在主持人确认后,按下复原按钮 ,状态指示灯重新点亮,并且同时发出"笛-笛-"声,为下一次抢答作好准备.(the Responder for up to four teams or individuals in the use of Responder competition occasions. Every team installed the seats before a Responder button switch (with the board S9, S10, S11, S12), and a signal (D4, D5, D6, D7). Moderator seats installed before a recovery switch (S3 board), a buzzer (BUZ1 board) and a Responder work status indicators (D10), whenever the moderator after oral orders issued. Which team first press of a button switches, the seat lights were lit on the first, while the blockade of the other button to switch activities. Moderator seats and extinguished the lights and the state issued three sound similar to the telephone tips ringing sound, in a statement this Responder action has been completed. the presenters confirmed? recovery button, status indicators re-lit,)
说明: 簡單的串列埠自我測試持式 測試硬體電路是否正確(Chuanlibu simple self-test with tester hardware circuit is correct)
说明: 适用与MCS-51系列单片机的维根26转RS232驱动程序(汇编语言).(apply and MCS-51 microcontroller series of 26-dimensional turn RS232 driver (assembly language).)
说明: ht47r20遥控程序,红外线载波输出频率这系统时钟的12分频,当系统频率为480KHZ,载波频率为40KHZ(ht47r20 remote control procedures, infrared output carrier frequency system clock frequency of 12 minutes, when the system frequency for 480KHZ, carrier frequency 40KHZ)
说明: MCS51系列单片机实现的16X2的LCD的数据显示(MCS51 MCU series of 16X2 LCD data)