▍1. STM32 硬件SPI_中文显示测试源码
基于STM32F103的ST7735s芯片的LCD中文显示例程(LCD Chinese Display Routine Based on ST7735s Chip ST32F103)
基于STM32F103的ST7735s芯片的LCD中文显示例程(LCD Chinese Display Routine Based on ST7735s Chip ST32F103)
说明: 基于STM32F103的ST7735s芯片的LCD中文显示例程(LCD Chinese Display Routine Based on ST7735s Chip ST32F103)
stm32控制超声波精确快速测距,误差在0.1cm,通过LCD显示测量值(STM32 control ultrasonic quick and accurate location, the error in 0.1cm, as revealed by LCD measurements)
STM32解算MPU6050工程文件,IIC读取6050数据,带DMP 。(STM32 calculation of MPU6050 engineering documents)
液晶240*128驱动 用的是PIC单片机 但是可以改 51单片机 里面驱动都一样 就是 拿过来就可以用 (LCD 240* 128 drive using a PIC microcontroller, but can be changed inside the microcomputer 51 is to take over the same driver can be used)
STM32F1与FPGA通过SPI进行通信,我上传的是32部分的程序,已经通过串口测试成功。此程序可拓展为和单片机,DSP通过SPI进行通信(STM32F1 and FPGA communication through the SPI, I uploaded the 32 part of the procedure has been successfully tested through the serial port. This program can be extended to and single-chip, DSP communication through the SPI)
240128液晶驱动的测试程序,c语言编写(240,128 LCD driver testing procedures, c language)
STC MCU + TM1812应用开发案例程序(STC MCU + TM1812 application development case program)
1、使用DS1302芯片实现自动更新时间功能 2、使用定时器实现秒表功能 3、使用1602液晶显示屏显示内容 4、可以通过按键设置时间(1, using the DS1302 chip to automatically update the time function 2, using the timer, stopwatch function 3, using the 1602 LCD display content 4, via the button to set the time)
新型增强型的SST 51单片机的开发工具和资料,包括在线仿真功能,在线编程下载功能,内部FLASH和SRAM的读写源程序,是51单片机开发工程师的第4代开发利器.(new enhanced the SST 51 MCU development tools and information, including online simulation, the ability to download online programming, internal FLASH and SRAM source literacy is 51 MCU development engineers in the development of fourth-generation weapon.)
T6963_COB_240X128点阵屏测试代码,T6963初始化测试程序,画圆,画线,画矩形。(T6963_COB_240X128 ,T6963 init)
stm32主控芯片实现对T5557卡的读写,资料包括读卡电路,T5557卡片的相关技术文档,上位机及工程源码。(The main control chip of STM32 realizes the reading and writing of T5557 card, including the reading circuit, the related technical documents of T5557 card, the host computer and the engineering source code.)
这是一个基于STC单片机,采用分离原件的125K的ID读卡器全套设计资料,其中包括原理图、PCB以及单片机源程序,还有我做设计时的参考资料。内容很全面的,以及在实物上验证过,可以正常运行。主要使用的天线为820uH。(This is based on STC microcontroller, the separation of the original 125K ID card reader full design information, including schematics, PCB and microcontroller source code, as well as I do the design reference. Content is very comprehensive, and verified on the kind, can operate normally. The main antenna is 820uH.)
4463收发程序 SPI 可实现稳定收发 基于STM32F103C8T6(4463 TX RX code MCU IS STM32F103C8T6)
使用stm32开发板的ADC进行1000Hz采样后,通过ESP8266wifi模块将数据传输至PC端。(After 1000Hz sampling with ADC of STM32 development board, data is transmitted to PC through ESP8266 WiFi module.)
说明: 使用stm32开发板的ADC进行1000Hz采样后,通过ESP8266wifi模块将数据传输至PC端。(After 1000Hz sampling with ADC of STM32 development board, data is transmitted to PC through ESP8266 WiFi module.)
基于示波法的电子血压计程序,包括脉搏测量。控制器采用STM32F103C8T6。包含数据核心算法程序。( Based oscillography electronic sphygmomanometer procedures, including pulse measurements. Controller uses STM32F103C8T6. It contains data core algorithm program.)
嵌入式开发校验最全C源码,包括(CRC8、CRC16查表法及算术法校验、异或和校验、和校验、校验和补码等)、校验工具,校验文档。全部为工程实际项目本人使用的源代码。( Embedded developers the most complete C source code verification, including (CRC8, CRC16 checksum table method and arithmetic method, XOR and parity, and parity, parity, and complement, etc.), calibration instruments, calibration documentation. All actual project I used for the project s source code.)
嵌入式开发校验最全C源码,包括(CRC8、CRC16查表法及算术法校验、异或和校验、和校验、校验和补码等)、校验工具,校验文档。全部为工程实际项目本人使用的源代码。( Embedded developers the most complete C source code verification, including (CRC8, CRC16 checksum table method and arithmetic method, XOR and parity, and parity, parity, and complement, etc.), calibration instruments, calibration documentation. All actual project I used for the project s source code.)