说明： 首先它能显示环境的温度并能设置上下限阀值，这是最基本的功能，系统上电的时候显示的是当前环境温度和设定的温度阀值，我们可以通过按键来修改温度上下限阀值。(First of all, it can display the environment temperature and set the upper and lower limit threshold, which is the most basic function. When the system is powered on, it displays the current environment temperature and the set temperature threshold. We can modify the upper and lower limit threshold by pressing the key.)
说明： 在stm32f407的平台下，进行TCP的客户端数据收发(On the platform of stm32f407, we can send and receive TCP client data)
说明： 在stm32f407的平台下，进行TCP的服务器端数据收发(Under the platform of stm32f407, the server-side data of TCP is sent and received)
说明： 实现电池的充放电功能，恒流充电、恒压放电，充电电流步进可调，步进值0.1A，电流控制精度6%。充电变换器的效率为85%。(The charging and discharging function of the battery is realized, including constant current charging and constant voltage discharging. The charging current can be adjusted step by step, the step value is 0.1A, and the current control accuracy is 6%. The efficiency of the charging converter is 85%.)
基于贝瑞隆模型的变压器保护，自己做的结课作业，绝对自己编写。(Bergeron model based transformer protection, their own job to do guitar lessons, write your own absolute)
用C语言写的RX8025T时钟芯片程序。 (this is a RX8025T real time chip driver program in C-Language.)
本程序提供sunson lcd CA320240 的源码。可以显示数字、汉字、图案等。(This procedure provided the source sunson lcd CA320240. Can show figures, Chinese characters, patterns and so on.)
说明： 此程序是LPC2119两路CAN程序 ，已经成熟用在产品上 并且很稳定(This program is CAN LPC2119 two procedures used in the product is mature and very stable)
说明： N76E003实现温度传感器DS18B20的串口打印(N76e003 realizes serial port printing of temperature sensor DS18B20)
RX8025T时钟芯片的驱动程序，区别于RX8025AC，亲测可用，可写，读取年月日时分秒周(RX8025T clock chip driver, distinguished from RX8025AC)
STM32F103控制继电器输出，可扩展应用至其他程序(STM32F103 Control Relay Output)
说明： STM32F103控制继电器输出，可扩展应用至其他程序(STM32F103 Control Relay Output)
说明： 1.系统整体设计 系本设计采用STC89C52单片机为主控芯片，结合外围电路矩阵键盘、液晶显示器LCD1602等部分组成,能够实现： 1 DS18B20不断采集周围环境温度； 2． 单片机处理温度的数据显示在DS18B20； 3． 用户设定温度报警的上限和下限；(1. Overall design of the system This design uses STC89C52 single chip microcomputer as the main control chip, combined with peripheral circuit matrix keyboard, liquid crystal display LCD1602 and other parts DS18B20 continuously collects the ambient temperature; 2. The temperature data processed by MCU is displayed in DS18B20; 3. The user sets the upper limit and lower limit of temperature alarm;)
用Matlab2012搭建的HERIC拓扑单相并网逆变器仿真模型，可以正常运行。(HERIC Single Phase Invertor Simulator Model。)
用Matlab2012搭建的HERIC拓扑单相并网逆变器仿真模型，可以正常运行。(HERIC Single Phase Invertor Simulator Model。)
12864中文字库液晶演示程序 MS12864R 测试程序(串口) 连线表 CPU=89C52 SystemClock=12Mhz CS=P3.0 SCLK=P3.1 SID=P3.2 Reset=RC in Board()
12864驱动程序（51串行）已通过检测，用时注意端口的定义(12864 Driver (51 serial))
说明： 在此基础上，设计一种温度测量系统，能够检测温度，并通过按键调整温度的上下限值，若超过该限值，进行报警提示。该系统的硬件子电路主要用Protues仿真软件实现，具体的子电路包括：恒流源电路（TLC2543芯片）、信号放大调理电路（两线制铂电阻PT100）、单片机最小系统（AT89C51）、A/D转换电路、按键电路、显示电路、声光报警器等。该系统的软件电路以C语言为基础，在Keil中实现。最后通过软硬结合，实现电路的各种情况仿真，以此验证电路设计的正确性和合理性。(On this basis, a temperature measurement system is designed, which can detect the temperature and adjust the upper and lower limits of the temperature by pressing the key. If it exceeds the limit, an alarm will be given. The hardware sub circuit of the system is mainly realized by Proteus simulation software. The specific sub circuits include: constant current source circuit (TLC2543 chip), signal amplification and conditioning circuit (two-wire platinum resistance PT100), minimum system of single chip microcomputer (AT89C51), a / D conversion circuit, key circuit, display circuit, sound and light alarm, etc. The software circuit of the system is based on C language and implemented in keil. Finally, through the combination of hardware and software, the circuit simulation is realized to verify the correctness and rationality of the circuit design.)
本站资源：696518 个
本站会员：104316 个
总计下载：494603 次
今日上传：0 个
Copyright© 2019-2025 |
Powered by Imdn
|
浙ICP备16007336号
|
|
联系客服（QQ：3324461878）
本网站资源收集自网络及网站用户上传，若有侵权请邮件至（3324461878@qq.com），核实后我们会在24小时内删除，谢谢！
